Driver Side LED Light to Go with Optronics Trailer Taillight STL14RB

Question

Question:

Im thinking of purchasing the 6 function led rectangle trailer lights but I dont see the one for thr driver side. what gives

asked by: Leroy B

0

Expert Reply:

For the drivers side light to go along with the part # STL14RB that you referenced you would want the part # STL15RB. This is the matching light you are looking for.

expert reply by: Jameson C

0

Answer 1

The LED Combination Trailer Tail Light part #STL14RB would be a suitable replacement for the passenger side tail light on a 2019 Bass Tracker Trail Star Trailer. If ever needed, we also have part #STL15RB for the driver side.

view full answer...

Answer 2

Yes, if you had no need for a license plate light you could use the LED Optronics trailer light part #STL14RB on either side of your trailer. It would just need to be flipped over like you mentioned so that the reflector is on the right side.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 9

Yes, 14 gauge wire seems too small. I would go with 10 or 12 gauge. For 10 gauge you can use #10-1-1 and for 12 gauge use #12-1-1. These wires are sold in increments of 1 foot. So if you needed 20 feet of wire you would enter 20 in the quantity box.…

view full answer...

Answer 10

Trailer wiring generally uses 16 gauge wire, part #16-1-1. However, with a long trailer like yours you may want to go with a larger like 14 gauge #DW07550-1 or even 12 gauge #12-1-1. Each size is sold by the foot. You will need to have the lights at…

view full answer...

Answer 11

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

view full answer...

Driver Side LED Light to Go with Optronics Trailer Taillight STL14RB

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching