What is the Mounting Hole Spacing for Motorhome Hitch 5350

Question

Question:

I want to replace a Reese receiver with the 5350 more towing capacity. Where can I find out the mounting bolt pattern? Im hoping to luck out and not have to drill new holes. Thanks

asked by: Mike R

0

Expert Reply:

Motor home hitch # 5350 features two holes on each side bracket for mounting the hitch to your frame.

The bolt holes are spaced 8-5/8 inches apart, center to center, and are 1/2 of an inch in diameter.

I have included a link to the installation instructions for the hitch.

expert reply by: Sarah L

0

Answer 1

I checked with Curt and they told me that the distance you are looking for on the Curt hitch part #C13702 is 6-3/8 inches and on the Draw Tite #5350 is 5-3/8 inches.

view full answer...

Answer 2

Hi Ryan; I don't have a drawing from Curt but we have gotten measurements on this hitch in the past. I attached three pictures below with different measurements for the #C14355. If you need a different measurement let me know and I will get that…

view full answer...

Answer 3

I reached out to my contact at Curt and was able to get a dimension sheet for the Curt Trailer Hitch Receiver - Class V #C15810 referenced in your question. I have attached an image of it for your review. This trailer hitch is designed to fit select…

view full answer...

Answer 4

I was able to get a dimension sheet from my contact at Curt for the Curt Hitch part #C15800 that you referenced. See attached pic. I also attached a set of the installation instructions for this hitch.

view full answer...

Answer 5

It is true that the center of the rearmost bolt holes for the Curt Trailer Hitch Receiver #C14355 measure 32-11/16" on center, but since these bolt holes are oblong this trailer hitch will still fit your 1999 Ford F-250. If you note in the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

What is the Mounting Hole Spacing for Motorhome Hitch 5350

Continue Researching