Suspension Enhancement Recommendation for 2013 Ford F-150 with Camper and Tools in Bed plus Trailer

Question

Question:

i have a 2013 f-150. With a 300 lb aluminum camper shell with 350lbs tools in the truck. 5 liter engine 3.55 diff. and tow a 6500 lb trailer 6 weekends a year. Rear suspension is a bit spongy without trailer. With trailer very spongy. Hat can I do to the rear suspension to help.

asked by: Greg E

0

Expert Reply:

Suspension enhancement like the Firestone Ride-Rite Air Helper Springs # F2525 would be a great choice for you. This will give you support for the rear suspension of your vehicle so that it feels less spongey with and without a trailer. Since the air pressure is adjustable you would be able to adjust the amount of support you need by inflating or deflating the bags when needed.

To make that easier you could get a compressor kit like part # F2158.

I attached install videos for both products I mentioned.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 9

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

Hey Douglas, whenever available I recommend going with the HD version of the Roadactive kits like the part #RAS3611-YHD that fits your 2022 Ford F-150 4WD. The extra capacity of this kit over the non-HD basically doesn't have any downside aside…

view full answer...

Answer 12

Hello Dan, Great question. When you’re comparing the Firestone kits #F59VV and #F2582, they both technically fit your 2025 F-150, but they are designed around different mounting locations and truck configurations. The #F2582 is the traditional…

view full answer...

Suspension Enhancement Recommendation for 2013 Ford F-150 with Camper and Tools in Bed plus Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching