LG-1 Landing Gear Repair Kit Recommendation and Install Diagram

Question

Question:

Do you have a diagram for how the repair kit for the gears go, everything on mine are spinning but wont go up or down

asked by: Barry W

0

Expert Reply:

The correct repair kit for the # LG-1 lead leg is part # LG-146059 and for the follower leg it's part # LG-146060. I attached a diagram that shows how these kits will install.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Repair kit #LG-146059 contains 2 pins and the drive shaft all of which are for the top of the jack. To help I have included the written instructions below and also a diagram that points out the parts mentioned in the written instructions. The…

view full answer...

Answer 2

Repair kit #LG-146059 contains 2 pins and the drive shaft all of which are for the top of the jack. To help I have included the written instructions below and also a diagram that points out the parts mentioned in the written instructions. The…

view full answer...

Answer 3

The installation of the Landing Gear Set part #RVLG-8000 will be fairly straight forward. Basically, you will need to have a metal support structure so you can attach welded tabs part #LC113511 to it, 15-1/2" apart. Once these are installed you…

view full answer...

Answer 4

It sounds like the screw itself is damaged if the motor and gears are turning but the leg isn't moving. Atwood no longer is in the 5th wheel landing gear business so I recommend replacing your landing gear completely. The reason you would need to…

view full answer...

Answer 5

I believe we may have what you are looking for, but to answer your question the Spring-Loaded Pull Pin for etrailer and Ram 5th Wheel Landing Gear #RVLG-SPP is designed for Landing Gear Set #RVLG-8000 which has a 2-1/2" square leg and a…

view full answer...

Answer 6

You have a few choices for replacement landing gear with legs that measure 29-1/2 inches, depending on what weight capacity you need and if you want manual or electric landing gear. - Stromberg Carlson #LG-1: Electric Landing Gear with 5,500 lb…

view full answer...

Answer 7

Both the Replacement Motor #LG-196308 and #LG-142178 have the same mounting dimensions but, like you said the 196308 has a higher weight capacity at 6,500 lbs. The only other notable difference is that the 142178 has a motor speed of 5,500 rpm while…

view full answer...

Answer 8

I checked the Spring Loaded Pull Pins #RVLG-SPP, #LG-119113 and #UF17-943031 that we have that are designed to replace those that are on your Lippert landing gear with the 3/8" pins and they all measured at 2-5/8" long from the mounting…

view full answer...

Answer 9

I went out to our warehouse so I could take a couple measurements on the etrailer.com Landing Gear Set #RVLG-8000 referenced in your question. From the center of the cross shaft to the bottom of the top weld stop I measured a distance of right at 7…

view full answer...

Answer 10

Thank you for providing that information and calculation. Based on your 1716 pin box and the 3,036 lb tongue weight you need the Gen-Y Hitch #GY48FR. However, there will likely be some clearance issues unless your trailer has a tapered nose since…

view full answer...

Answer 11

Since your Venture leg is the follow leg the repair kit is #LC146060. If you had the lead leg it would be #LC146059.

view full answer...

Answer 12

You should need repair kit #LG-146059 for the lead leg and #LG-146060 for the follower leg. From the picture you sent in I was able to determine that you have a Venture landing gear set VMC900R.

view full answer...

LG-1 Landing Gear Repair Kit Recommendation and Install Diagram

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching