Size of Wrench Needed and Torque Spec for the B and W Hitch Ball # BWHB94009

Question

Question:

This nut is what size and whats the toqure? Please include these specks in all Vids and scrips.

asked by: Marc P

1

Helpful Expert Reply:

I spoke to my contact at B and W and he informed me that the size wrench needed to tighten the nut of the # BWHB94009 would be a 2-15/16 inch and should be tightened to 120 ft lbs.

expert reply by: Jameson C

1

Answer 1

I went out to our warehouse to take a look at the B&W 2-5/16 Inch Hitch Ball #BWHB94009 referenced in your question. From where the shank starts up to the top of the hitch ball, there is a distance of 3-1/4 inches. I have included an image with…

view full answer...

Answer 2

I called my contact at B&W about the 2-5/16 Inch Hitch Ball, part #BWHB94009. They told me this there are 4-1/2 threads per inch so it would be considered a coarse thread Ball shank.

view full answer...

Answer 3

It looks like you have an old Valley Stow-A-Ball Gooseneck but it also looks like it is incomplete. Valley is no longer in business so that ball is no longer available. I've attached a photo of that style ball to help. There is not a gooseneck…

view full answer...

Answer 4

I went out to the warehouse and found that the nut that comes with the B&W 2-5/16" Hitch Ball #BWHB94009 is 1-3/4" tall as you can see in the attached picture. The 2" diameter shanks that we have are all 3-1/2" long so there…

view full answer...

Answer 5

You could use the B and W Hitch Ball part #BWHB94009 as a gooseneck ball like you are wanting as it has a 30k capacity is threaded and has a nut and washer.

view full answer...

Answer 6

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Size of Wrench Needed and Torque Spec for the B and W Hitch Ball # BWHB94009

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching