Brackets and Wiring for Sealed, Miro Flex, Mini Thin Line LED Marker or Clearance Light # AL191AB

Question

Question:

I just recvd my AL191AB Miro Flex thin line LED Lights 3. Something is missing ...I have no way to mount this to the trailer. Is there a mounting plate and wiring connection for these units.

asked by: William F

0

Expert Reply:

We do have the parts you need to complete installation of the light. But first, sealed, Miro Flex, Mini Thin Line LED Marker or Clearance Light # AL191AB does not include a base or wiring harness. We have the compatible bases listed as related products on the right hand side of its product page.

There is flush mount grommet, # A91GB
Self-grounding black bracket, # A91BB
Black bracket with open back, # A91BOB
Chrome bracket with open back, # A91OB
Self-ground chrome bracket, # A91CB

For a wiring harness use # A46PB for open back brackets or # A91LW for self-grounding brackets.

expert reply by: Michael H

0

Answer 1

I have a solution for you, but we don't have any clearance lights that would mount with the white bushing you're referring to. If you went with the #AL191AB and #AL191RB like you mentioned you would need the #A91BOB mounting plates to mount…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Brackets and Wiring for Sealed, Miro Flex, Mini Thin Line LED Marker or Clearance Light # AL191AB

Products Featured in This Question

Continue Researching