Installation Bolts for the CE Smith Hanger Bracket part # CE14017G

Question

Question:

What bolt size is used to install the bolt-on spring hangers CE14016G and CE14017G?

asked by: Stephen

1

Helpful Expert Reply:

The mounting holes of the part # CE14017G and # CE140116G that you referenced are 7/16 inches in diameter. You would need to get bolts that would fit those hole sizes. Since applications can vary there isn't a set bolt size you would need. Your best option would be to find a bolt long enough for your application that would fit in the hole.

expert reply by: Jameson C

1

Answer 1

From the ground to the top of the crossbars when the the Yakima Rack and Roll Trailer, #Y08106, is level, it measures 22 inches. The Heavy Duty Shocks, #Y08110, is using the terms shocks as an all encompassing term that covers the shock itself and…

view full answer...

Answer 2

The only bolt-on hangers we have for 1-3/4" slipper springs come from CE Smith: - Front #CE14016G - Rear #CE14017G Attached are some review videos for you to check out!

view full answer...

Answer 3

Hey Caleb, unfortunately you can't use slipper springs with a radius end like the 3-Leaf Slipper Spring w/ Radius End for 1,500-lb Trailer Axles #e99SR because the brackets are different. You could use open eye springs like #e24SR to replace your…

view full answer...

Answer 4

Your trailer uses an open eye leaf spring like #e24SR. Over time as the leaf spring softens the gap you are seeing will get bigger. As long as the leaf spring is not falling off the hanger when you raise the trailer weight off the axle they do not…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Installation Bolts for the CE Smith Hanger Bracket part # CE14017G

Product Page this Question was Asked From

Continue Researching