How To Find Bearing Replacement For Harbor Freight Trailer
Updated 03/04/2020 | Published 08/18/2014
Question:
Do you know what size bearings fit the Harbor Freight 5002 trailer? My instruction manual does not specify the dimensions. Any ideas? Thanks,
asked by: Chris
Expert Reply:
In order to find the best replacement bearings and seals for your Harbor freight Trailer, you will need to remove the wheel and hub and pull the bearings, seals, and races off your spindle. I have attached a photo that shows where you can find the numbers on those items.
If you are not able to find the numbers on these items, you will need to take some measurements of the spindle with a precision instrument like a digital caliper in the locations as shown in the attached photo.
Typically, Harbor Freight uses non-standard size bearings and it may be difficult to find any that would work for you. If you wish to give the dimensions, we can make a recommendation for a replacement axle that would work on your trailer.
I have also included a helpful article that shows how to replace the bearings, races and seals you can check out.
Product Page this Question was Asked From
Bearing Buddy Bearing Protectors - Model 2047 - Chrome Plated - Qty 2
- Trailer Bearings Races Seals Caps
- Caps
- Bearing Protector Grease Cap
- 2.05 Inch
- 2000 lbs Axle
- Bearing Buddy
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Kenda Karrier S-Trail ST145/R12 Radial Tire w/ 12" White Spoke Wheel - 5 on 4-1/2 - LR D
- Q&A: Recommended Stabilizer Jacks for a Rpod Trailer
- Q&A: Upgrading the Tire and Wheel on a Harbor Freight Trailer
- Video: Kenda 4.80-12 Bias Trailer Tire with 12" White Wheel Feature Review
- Video: Review of Taskmaster Trailer Tires and Wheels - Tire with Wheel - TA49QR
- Q&A: Can a 5.30-12 Size Tire be Replaced with a ST145/R12 Size Tire
- Shop: etrailer Scissor Stabilizer Jacks w/ Handle and Drill Adapter - 24" Lift - 5,000 lbs - Qty 2
- Search Results: 53x12
- Shop: Kenda 4.80-12 Bias Trailer Tire with 12" White Wheel - 4 on 4 - Load Range B
- Shop: Taskmaster 4.80R12 Radial Trailer Tire w/ 12" Vesper White Spoke Wheel - 4 on 4 - LR C
- Shop: Replacement Trailer Wheel Bearing - L44649 - Qty 1
- Shop: Kenda 4.80-12 Bias Trailer Tire with 12" Galvanized Wheel - 4 on 4 - Load Range C
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Search Results: stabilizer jacks trailer jack
- Search Results: ratchet straps
- Search Results: scissor jacks camper jacks
- Search Results: trailer lock
- Search Results: goshen
- Video: A Closer Look at the etrailer Scissor Stabilizer Jacks with Handle and Drill Adapter
- Video: Review of etrailer Camper Jacks - Scissor Stabilizer Jack Qty 2 - e56VV
- Search Results: harbor freight trailer
- Q&A: How Often Should Bearings Be Greased And How Much Grease Should I Add?
- Video: Feature Breakdown: Grease Seals (pair)
- Video: Checking Out the Taskmaster 5.30R12 Radial Trailer Tire
- Q&A: Will etrailer Trailer Axle With Idler Hubs Fit Harbor Freight Trailer
- Q&A: How to Pick Out Replacement Trailer Axle for Harbor Freight Trailer
- Q&A: Do Harbor Freight Trailers with 5 Bolt Pattern Use Standard 5 Bolt Pattern
- Video: A Closer Look at the Valterra Gray Water Drain Connector
Deric
3/3/2020
Hello, can you help me find replacement bearings and seals for my harbor freight trailer? The numbers on the bearings and races are the same it says 30205 on one end and HCH on the opposite. On the seals Im not sure if its: TC 30 52 10 or TC305210 or TC 305210. The seal ring has shallow grooves cut out along the outside face. The grooves are evenly distributed like how a pizza would be cut, and between each groove it has TC on one, 30 on the next, 52 after that and then 10. Does this help?