How to Wire LED Side Marker Lights on a Freedom Folding Trailer
Updated 10/30/2026 | Published 10/27/2026 >
Question:
I am assembling a freedom foldable trailer. After installing the wiring and figuring out the grounding issue, I managed to get the tail lights to functions properly LED Type. However, I cant get the side running lights to work. The wiring diagram with the trailer see photo is no help as it only shows one wire from the running light the black one connecting to the brown wire of the harness. The running light is LED with a red and black wire. I hooked it up this way and put the red to ground. No joy. Thoughts?
asked by: Stu
Expert Reply:
Good morning Stu,
The brown wire powers both the tail lights and side marker lights, so you've got the right circuit!
My suspicion is that your LED wires are reversed. Typically, red is positive and black is ground for 12V DC lights, so try connecting red to brown and black to ground. LEDs are usually polarity-sensitive.
You'll have a brown wire running along each side of the trailer to connect to the corresponding side marker's red wire. The marker's black wire then connects to a clean, bare-metal ground on the trailer frame. This is common on wishbone 4 way flat setups like # A20WB.
If that doesn't work, do you have a part number for those side marker lights? I can help confirm the wiring!
Product Page this Question was Asked From
20 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 30" Ground
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- 4 Flat
- Plug and Lead
- Optronics
more information >
Continue Researching
- Search Results: bt8 spindle
- Shop: Trailer Idler Hub Assembly for 2K Axles - 10" to 12" Wheels - 5 on 4-1/2 - Pre-Greased
- Shop: Trailer Idler Hub Assembly for 2K Axles - 10" to 12" Wheels - 5 on 4-1/2 - Pre-Greased
- Shop: Replacement Trailer Wheel Bearing - L44649 - Qty 1
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Hitch
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Search Results: trailer tires and wheels
- Article: Trailer Wiring Diagrams
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Shop: Trailer Wiring
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Drum - AKHD-545-35-EZ-K
- Search Results: trailer hubs and drums
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: Comparing the eTrailer and Dexter Electric Trailer Brake Kits
- Shop: Brake Controller
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Search Results: trailer brakes
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Suspension Enhancement
- Article: Electric Trailer Brakes: How They Work & What to Buy
- Search Results: trailer jack
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Video: etrailer VS Dexter Self Adjusting Brakes Comparison
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Video: Hands-On with the Hub Saver Hub and Wheel Protector
- Q&A: What Is the Difference Between a BTR and BT8 Spindle
- Search Results: trailer leaf springs
- Shop: Gooseneck Hitch



Stu
10/30/2026
Thank you Andrew. Funny enough I originally wired the red to power and the black to ground without looking at the wiring diagram (retired Avionics maintenance engineer) as experience would tell me. When none of the trailer lights worked, I checked the wiring diagram which only shows the black wire connected to power. So I reversed the leads only to find the ground return was my problem. After fixing the ground return all the other lights worked. This is when I contacted you and of course returning the red to power and the black to ground solved my issue.