Is There Specific Setting for Lithium Battery for Victron SmartSolar 100/50 MPPT Solar Charge Contro

Question

Question:

is there a specific settings for lipo batteries? AND why is the app displaying 0 in solar watts ?

asked by: Jeff F

0

Expert Reply:

Hey Jeff, yes the Victron SmartSolar 100/50 MPPT Solar Charge Controller # VN92VR that you referenced does have a LifePo battery setting you would need to use and the reason the app is displaying 0 in solar watts is because the battery is fully charged so the controller isn't feeding it anymore charge. Is your battery topped off that you are aware of?

expert reply by: Jameson C

0

Jeff F.

8/5/2026

no my batteries were completely dead ( i believe they have a low voltage cutoff built in). I had to connect to the grid to charge them. I have since found the lipo setting. good there, but I still cant get solar to charge batteries. thx

Jameson C.

8/5/2026

@JeffF if the batteries are super dead then that's why. It needs to sense a battery and if it's totally dead it doesn't think a battery is connected.

Jeff

8/5/2026

I can see solar voltage but no watts.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Is There Specific Setting for Lithium Battery for Victron SmartSolar 100/50 MPPT Solar Charge Contro

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching