Will The ShakeStopper Bumper Hitch MNT72VR Work For Carrying Two Electric Bikes?

Question

Question:

I have a 2004 Keystone Cougar 5th wheel with an aluminum covered 4inch tube steel rear bumper. Will this work? If not, what other options are there for adding a 2inch receiver for 2 electric bikes?

asked by: David F

0

Expert Reply:

Hey David, thanks for reaching out. The ShakeStopper Heavy Duty 2" Hitch Receiver for 4" RV Bumpers # MNT72VR can absolutely work for carrying a few electric bikes. The hitch itself has a 400 lb capacity so that will be more than enough. The real limiting factor here is the weight capacity of your bumper. Bumper capacities can vary so you'll want to check with a dealership and verify your bumper can hold the weight. As long as the bumper is up to the task, and you get a good RV rated bike rack you'll be good to go.

Do you already have a bike rack you were planning on using? What kind of bikes do you have?

expert reply by: Jesse M

0

ShakeStopper Heavy Duty 2" Hitch Receiver for 4" RV Bumpers - 400 lbs
(click to enlarge)

Answer 1

Hey Alexandria! Bike racks rated for travel trailers are pretty limited. There is quite a bit of additional force back there. This also means there are no 1-1/4" bike racks that will work. I have two different options for you. The first is to…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Will The ShakeStopper Bumper Hitch MNT72VR Work For Carrying Two Electric Bikes?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching