Mount your bike rack or cargo carrier above or below your 4" x 4" RV bumper. Hitch receiver tightens around your RV bumper using a heavy-duty retention fastener. Clamp-style design holds your shank in place to reduce rattling and damage.
Features:
Specs:
Note: Bumper weight capacities vary by manufacturer. Please be sure to verify the weight capacity of your bumper with the manufacturer prior to loading.
The ShakeStopper gives you the flexibility to mount your hitch above or below your RV bumper. You can mount your hitch receiver below the bumper if your camper body hangs over your bumper. You can also mount it above to give your bike rack or cargo carrier an extra 6" of clearance to avoid scraping on uneven surfaces when entering or leaving parking lots or crossing roads.
No more loud, shaky rides and damage to your bike rack or cargo carrier. Unlike conventional bumper-mounted hitches that often tighten down the shank using set screws that cause instability and dents, the ShakeStopper has a unique clamping design that firmly holds your bike rack or cargo carrier in place to help reduce noisy rattling and avoid damage to your shank from rocky, bumpy rides.
The shank is held in place between a 1/4" steel base plate and 2 free-floating pressure plates. The heavy-duty retention bolts are used to tighten the pressure plates down, creating a clamping force to reduce movement of your hitch-mounted accessory. The base plate helps distribute the load when the pressure plates are engaged to prevent denting and other damage. Shank locks in place with a 5/8" hitch pin and clip (sold separately).
Most bumper-mounted hitches use load-bearing fasteners, such as U-bolts, to carry the weight of hitch-mounted accessories, like a bike rack or cargo carrier. The bolts can easily dent your bumper if over-tightened and tend to loosen over time, causing your hitch to bounce and shake while driving down the road, leading to more damage on your bumper. This unique design was constructed with a retention fastener to firmly clamp the side plates and base plate around your bumper to reduce the risk of damage.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello, neighbor! Steven here with etrailer.com. Let's take a look together at our ShakeStopper heavy duty two-inch hitch receiver for your four-inch RV bumpers and it's rated at four hundred pounds. So folks, a lot of times you get a bumper-mounted hitch receiver. A lot of 'em have those big U-bolts and stuff, they're cumbersome to put on and they can actually damage your square bumper. Well, these guys here at ShakeStopper got an option for you. This bumper-mounted hitch receiver can mount either above or below that four-by-four bumper and it is designed specifically to fit the two-inch by two-inch bike rack and cargo carriers.
Again, up to four hundred pounds capacity. It does eliminate the most common failure points (object knocking) that are caused from load-bearing welds or bolts. And again, it's a clamp-on style, so it's going through that four-by-four bumper and it's using the whole grip like this from the bottom. (receiver knocking) And then on the top (hand tapping) you have a retention bolt here to help hold everything in place and press pressure down and around everything to help hold it in place. It's made and coated of a nice durable powder-coated steel to resist rust and corrosion.
And it's a super simple install. There's no drill required. You get all the plates and hardware included. It's made right here in the US, and it's approximately nine and a half inches tall, about five inches wide and four and three-quarter inches deep. Now, there are basically some pins up here on the top (receiver knocking) around that tension bolt.
Everything here is gonna come in a nice flat box. It does get put together by you when you get it. You just slide the pieces through the slots per the instructions. Tighten up everything around the bumper and you're on your way. A nice limited lifetime warranty.
This is the ShakeStopper heavy duty, two-inch hitch receiver for four-inch RV bumpers. I'm Steven. Thanks for watching.
Average Customer Rating: 5.0 out of 5 stars (1 Customer Reviews)
Mount your bike rack or cargo carrier above or below your 4" x 4" RV bumper. Hitch receiver tightens around your RV bumper using a heavy-duty retention fastener. Clamp-style design holds your shank in place to reduce rattling and damage.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.