Replacement Nut and Screw for an Older Bulldog 180 Series Jack

Question

Question:

I have a 180 series jack and the nut is stripped out. can you still get the older nuts?

asked by: Corey

0

Expert Reply:

I spoke to my contact at Bulldog and he informed me that the Replacement Screw and Nut Kit # BD500217 would work for your 180 Series Bulldog 12k Jack.

expert reply by: Jameson C

0

Answer 1

Thanks for getting in touch, Donnie. The Replacement Square, Direct Weld Jack Inner Tube #TJD-12000SP-FIP you mentioned is made for the Ram jacks such as part #TJD-12000SP-F2. So, this is really the only brand of jack I can recommend using it for. As…

view full answer...

Answer 2

We do have the Replacement Inner Tube with Drop Leg, Foot, and Pull Pin for Curt Heavy Duty Direct Weld Square Jack #C28957. This is a 3-1/2" x 3-1/2" square inner tube that is designed to replace the inner tube on the Curt 28512 jack. We…

view full answer...

Answer 3

I spoke to my contact at Bulldog who said that the Model 12, 180 Series Bulldog jack that you have is the older version of the the current 10K jacks like part #BD182500. Since you have the older version without the spring that you mentioned seeing in…

view full answer...

Answer 4

The Bulldog Square Jack, part #BD182800 and part #BD182815 are very similar but have just a couple of slight differences. They are both 26 inch lift jacks with a 10,000 lb weight capacity, and are sidewind jacks. The #BD182800 has a side-facing…

view full answer...

Answer 5

We do sell replacement screw and nut assemblies for Bulldog Jacks. Item #BD500250 fits Bulldog Jacks rated at 10,000-lb lift, 12,000-lb support. It has a rod diameter of 1-1/4 inches. We also offer Item #BD500217, which is designed for use with…

view full answer...

Answer 6

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 7

I've attached instructions to this question to give you a getter look at replacing the Bevel Gears #LC182851 in your HappiJac #LC736514 #LC736515. Unfortunately, I do not have a video for you but the instructions do provide good pictures. First…

view full answer...

Answer 8

To access the gears inside of the heavy-duty Bulldog jacks, like part #BD182415, you simply remove the screws that are holding on the plate covering the top of the jack. Once that plate is removed, the gears, pins and handle should be exposed. We…

view full answer...

Answer 9

I spoke to my contact at Bulldog and he told me that the pin you are trying to get out is a 5/32 grooved pin that will need to be tapped out with a punch like you mentioned. It's designed not to come out so you will need to hit it pretty hard.…

view full answer...

Answer 10

The Replacement Sungear and Subshaft for Bulldog 2-Speed Jack #BD500285 you will need to remove the gearbox cover with its 4 bolts. This will give you access to the planetary gears and this is basically the input part. I reached out to my contact at…

view full answer...

Answer 11

It sounds like either the motor is shot or the gears are worn. You're going to want to test the voltage of the motor first before deciding to replace it. If your motor is not getting enough voltage then you're just going to need to replace it…

view full answer...

Answer 12

We do have the replacement screw and gear kit for your 12K Bulldog 180 Series Jack. You will need Gear Kit #BD500212 and Screw and Nut Kit #BD500217. You will also need grease for the new gears, so if you don't have any use #L11316. I included a…

view full answer...

Replacement Nut and Screw for an Older Bulldog 180 Series Jack

Continue Researching