What is Hub Bore Diameter of Trailer Idler Hub # TRU33AV

Question

Question:

What size is the bore of the hub where the rim goes

asked by: Matt

0

Expert Reply:

Hey Matt, the bore of the Trailer Idler Hub Assembly for 3,500-lb Axles # TRU33AV that you referenced is 3.09 inches which is standard for 3,500 lb idler hubs like this.

expert reply by: Jameson C

0

Answer 1

Hi Richi! The etrailer Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 5 - Pre-Greased #AKIHUB-550-35-EZ-K you asked this question from fits all your specifications. It works with 3,500 pound axles (it uses the standard #L44649 and…

view full answer...

Answer 2

Hey JW, we have an idler hub like you are looking for with the part #AKIHUB-550-35-K or if you have trailer brakes and need a hub/drum you'd want the part #AKHD-550-35-K. These are both for 3,500 lb trailer axles, have the 5 on 5 inch bolt…

view full answer...

Answer 3

The Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 5 - Pre-Greased #AKIHUB-550-35-K should fit just fine with your Big Tex trailer, however I do recommend double checking the bearings and seal to make sure it matches with what you currently…

view full answer...

Answer 4

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

What is Hub Bore Diameter of Trailer Idler Hub # TRU33AV

Product Page this Question was Asked From

Continue Researching