Is Brophy Ball Mount for 2" Hitches Made In China

Question

Question:

IS BM20 MADE IN CHINA. WILL THE 40038 FIT ON MY BM20 HITCH

asked by: DEAN B

0

Expert Reply:

Hello again Dean. The Brophy Ball Mount for 2" Hitches # BM20 is made in the USA. Also yes, the 2" Hitch Ball # 40038 will fit the Brophy ball mount. It has a 1" diameter shank and is rated a bit higher at 12,000 lbs. Realistically, any hitch ball with a 1" shank and a rating to match the ball mount is a good fit.

expert reply by: Robin H

0

Made In The USA
(click to enlarge)

Jim

5/9/2026

Label on the ball mount states “made in USA”. Nice long mount.

Answer 1

Hey Glenn. I went down to the warehouse and measured the BulletProof Hitches 2" Hitch Ball item #BPH43RR. From the bottom of the shank to the top of the hitch ball is 5-1/4". This is a 2" hitch ball with a 10,000 lbs capacity. It has a…

view full answer...

Answer 2

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 3

Hey Rick, the part #e25ZV was not designed to be used with a trailer towing setup. Especially weight distribution as it adds quite a bit more strain on the setup. If you need more length from a weight distribution setup it's best to go with a…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The Brophy Ball Mount #BM20 and the Brophy #BH20 referenced in your question are extremely similar to each other. They are both designed for 2 inch trailer hitch receivers, have a 10,000 pound towing weight capacity, feature a long, 13-1/4 inch shank…

view full answer...

Answer 7

Hey Ted, thanks for reaching out. I went out to our warehouse and measured the Dexter Light Box Guard #DX99VC. The oval cutout is indeed 6-1/2" long x 2-1/2" tall. The 2" side light is supposed to be just a clearance light for…

view full answer...

Answer 8

The Timbren Suspension Enhancement System #T28MR is designed for your 2023 GMC Sierra 1500 both for heavy loads and unloaded. Do note that unloaded ride quality will be more stiff. The Timbren System #T53MR is their severe service kit. This is…

view full answer...

Answer 9

One thing to note when using a hitch extender like the etrailer, #e88YR, is that the tongue weight and towing capacity of your trailer hitch will be reduced by 50 percent due to the increased leverage that is placed on your trailer hitch from your…

view full answer...

Answer 10

I did some research and I think the Coachmen Mirada uses an H4 headlight bulb. In which case, the brightest option we offer for these is the H4 LED Headlight Bulbs part #ARC94VR which are LED and much brighter than the standard halogen you have now…

view full answer...

Answer 11

Hi Jeff; there is no maximum tongue weight rating on the etrailer High-Low Fixed Adapter #e25ZV. The adapter is only designed for flat towing, not a trailer or hitch accessory, so it was not tested or given a rating. Are you wanting to use this for…

view full answer...

Is Brophy Ball Mount for 2" Hitches Made In China

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching