Looking for Replacement Brake Assemblies and Hub/Drums for Lippert 4,400 lb Axle

Question

Question:

Looking for brakes and drums that will fit my axle Lippert axle 08/21/15 year Ser045-003442511 GAWR 4400 lbs Cust part0247644 LC144-SBSA-86-68.5-NOSP-0S-L-655-7278-18PT 6 wheel studes 16 wheels

asked by: Jim K

0

Expert Reply:

Hey Jim, thanks for all of the info you listed from your Lippert axle! Based on that the correct replacement hub/drums would be the part # 8-407-5UC3-EZ and then for brake assemblies part # LC46WD for the right hand side and part # LC96WD for the left hand side. What trailer do you have?

expert reply by: Jameson C

0

Rick

5/8/2026

It was a perfect fit. I like the self adjustment brakes, they work great.

Jameson C.

5/11/2026

@Rick that's awesome to hear!

Answer 1

Hello again, Ray. Good to hear from you. Your Dexter 635096 4,400 lb axle uses the Trailer Hub and Drum Assembly #8-407-5UC3-EZ. This uses the #L68149 (1.378" inner diameter) inner bearing and #LM67048 (1.25" inner diameter) outer bearing.…

view full answer...

Answer 2

With a Dexter 7,000lb axle and self adjusting electric trailer brakes you will likely have the Nev-R-Adjust Electric Trailer Brake Kit #23-464-465. There is a small stamped area on the outside of the backing plate which will give you information on…

view full answer...

Answer 3

If you have a self-adjusting brake assembly, you'll be able to see the adjuster cable extending across the brake assembly once you remove the hub/drum. However, we sell the Dexter brake kit #K23-463-00, so we can confirm the brakes are not…

view full answer...

Answer 4

Hello Wesley. The Lippert 4,400 lb axles use the same standard bearing and seal sizes as a 3,500 lb axle. So, for a full bearing kit you can use the #BK2-100 kit. The seal has a 1.719" ID and 2.565" OD, and for that you can use the Grease…

view full answer...

Answer 5

Hey Mario, the correct brake assembly set you need for the 4,400 lb axles on your trailer is the part #LC46WD and #LC96WD. Then for a hub/drum you'd want the part #8-407-5UC3-EZ and you'd be set. The hub includes all the needed bearings and…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Looking for Replacement Brake Assemblies and Hub/Drums for Lippert 4,400 lb Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching