How to Identify Self Adjusting Brakes Installed on Dexter 7,000LB Axle for 2019 North Point 377 RLBH

Question

Question:

I have a 2019 Jayco North Point 377 RLBH.It has 7000 axles.I need to replace the brakes.I have self adjusting brakes.Should be dexter.One side came apart and I have a spring hanging between the drum and backing plate.It is possible to find out what I have with out taking it apart?Probably need one drum.Thx for your help.

asked by: Mike

0

Expert Reply:

With a Dexter 7,000lb axle and self adjusting electric trailer brakes you will likely have the Nev-R-Adjust Electric Trailer Brake Kit # 23-464-465. There is a small stamped area on the outside of the backing plate which will give you information on the brake assembly or if you have the serial number for your Dexter axle I can use that to verify all the parts installed on your axle from the factory. This will allow me to know exactly what grease seals, bearings and other parts you might need as well without having to disassemble your hubs.

expert reply by: Bud M

0

Answer 1

Hey Jim, thanks for all of the info you listed from your Lippert axle! Based on that the correct replacement hub/drums would be the part #8-407-5UC3-EZ and then for brake assemblies part #LC46WD for the right hand side and part #LC96WD for the left…

view full answer...

Answer 2

Hello again, Ray. Good to hear from you. Your Dexter 635096 4,400 lb axle uses the Trailer Hub and Drum Assembly #8-407-5UC3-EZ. This uses the #L68149 (1.378" inner diameter) inner bearing and #LM67048 (1.25" inner diameter) outer bearing.…

view full answer...

Answer 3

If you have a self-adjusting brake assembly, you'll be able to see the adjuster cable extending across the brake assembly once you remove the hub/drum. However, we sell the Dexter brake kit #K23-463-00, so we can confirm the brakes are not…

view full answer...

Answer 4

Hey Mario, the correct brake assembly set you need for the 4,400 lb axles on your trailer is the part #LC46WD and #LC96WD. Then for a hub/drum you'd want the part #8-407-5UC3-EZ and you'd be set. The hub includes all the needed bearings and…

view full answer...

Answer 5

Hello Wesley. The Lippert 4,400 lb axles use the same standard bearing and seal sizes as a 3,500 lb axle. So, for a full bearing kit you can use the #BK2-100 kit. The seal has a 1.719" ID and 2.565" OD, and for that you can use the Grease…

view full answer...

Answer 6

Hello Jay, So, the good news is that yes, the CRE4000 #MR29DR can work with your 2023 Grand Design Imagine 2500RL. It’s built for tandem axle setups with axle ratings from 3,500 to 7,000 lbs, just like the CRE3000. As long as your axle spacing is the…

view full answer...

Answer 7

The best way to find the correct replacement for your equalizer is by measuring the distance from the front shackle hole to rear shackle hole on your current equalizer. The 33" AllTrek #MR89DR has the holes spaced 6-1/2" on center while the…

view full answer...

Answer 8

The difference between the two brake assemblies comes down to one being self adjusting and one that is manually adjusted. I recommend the self adjusting because you will never have to crawl under the trailer to adjust the brakes. This can be a…

view full answer...

Answer 9

It sounds like you might be searching for some replacement electric trailer braking assemblies or possibly just replacement parts. It's typically not much less cost effective to just replace the entire assembly so that's what I recommend. I…

view full answer...

Answer 10

The MORryde X-Factor Crossmember for CRE, SRE, or Stock Leaf Spring Suspension #MR33WR includes one adjustable crossmember. Your existing hardware will be too short due to the extra thickness of the crossmember, so you will need to add #MR58ZR if…

view full answer...

Answer 11

Yes, the MORryde X-Factor Crossmembers are available separately. We have one for Standard Hangers #MR33WR, for LRE, RE, or TRE Suspension #MR99ZR and one for a Dropdown Crossmember #MR84AR.

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

How to Identify Self Adjusting Brakes Installed on Dexter 7,000LB Axle for 2019 North Point 377 RLBH

Product Page this Question was Asked From

Continue Researching