What Grade Mounting Bolts are Needed for Installing the MORryde Cushioned 5th Wheel Pin Box for 14K?
Updated 04/15/2026 | Published 04/07/2026
Question:
I need to know the specs for the mounting bolts, grade 5 or 8
asked by: Luis S
Expert Reply:
Hello Luis,
Thank you for writing in!
When you install the MORryde Cushioned 5th Wheel Pin Box for 14K to 18K Trailers with Lippert Rhino, # MR83QR, you will need to use 5/8 inch by 11 Grade 5 mounting bolts. This matches the original hardware used by Lippert for the Rhino pin box and is the correct specification for this application.
Grade 5 hardware is intentionally used here because it provides the right balance of strength and flexibility. This helps prevent bolt shear and reduces the risk of damage to the mounting wings or trailer frame as the pin box absorbs road shock and movement. Using a higher grade bolt can make the connection too rigid and transfer more stress into the frame.
This pin box is designed as a direct replacement, so MORryde does not include new mounting bolts. The system is engineered to work with the same bolt grade and size as the factory setup. If your existing bolts are in good condition, they can be reused. It is a good idea to inspect them for any signs of corrosion, stretching, or damaged threads before reinstalling. If replacement is needed, be sure to use the same 5/8 inch by 11 Grade 5 bolts.
Out of curiosity, what are you towing and where do you like to take it? Always enjoy hearing where folks are putting their setups to use.
(click to enlarge)
Product Page this Question was Asked From
MORryde Cushioned 5th Wheel Pin Box for 14K to 18K Trailers w/ Lippert Rhino
- 5th Wheel Pin Box
- Upgraded Pin Box
- Reduces Chucking
- 24000 lbs
- Rubber Spring Suspension
- Fixed Turret
- Lippert Rhino
- MORryde
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: snappad rv jack pads
- Search Results: morryde cre3000
- Q&A: Does The Replacement Wet Shoulder Bolt MR52HR Come With The Lock Nut?
- Video: Review of the Replacement Wet Shoulder Bolt
- Shop: Replacement Wet Shoulder Bolt - MORryde Suspension Upgrade Kits - 9/16" x 2-15/16" - Qty 1
- Q&A: Looking for Replacement Bolt for MORryde Equalizer CRE3000
- Shop: Suspension Enhancement
- Shop: Replacement Pad for SnapPad Jack Stand Pad System - 11-1/2" or 12" Round Jack Foot
- Search Results: morryde lre
- Q&A: Replacement Wet Bolt for MORryde Suspension Upgrade Kit
- Shop: Trailer Wiring
- Shop: MORryde Suspension Upgrade Kit for Tandem Axle Trailers - 2-1/4" Long Shackle Straps
- Search Results: compartment door rv door locks
- Search Results: screen door rv door parts
- Search Results: challenger rv screen door parts
- Shop: MORryde Shock Absorbing Suspension Equalizers for Tandem Axle Trailers w/ 35" Wheelbase - 8K
- Shop: Replacement Wet Shoulder Bolt - MORryde Suspension Upgrade Kits - 9/16" x 3-3/8" - Qty 1
- Shop: Bronze Bushing - 9/16" Inner Diameter, 11/16" Outer Diameter - 1-3/4" Long - Qty 1
- Shop: Leaf Spring Bushing - Bronze - 1.74" Long x 0.70" OD x 0.58" ID - Qty 1
- Video: Installation: Hopkins Endurance 6-Way Trailer Connector Socket on a 2013 Chevrolet Silverado
- Video: Review of MORryde Trailer Leaf Spring Suspension - Replacement Rubber Shear Spring - MR79UR
- Q&A: Lift Kit Solution to Allow Fifth Wheel Trailer to Sit More Level When Towed
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
on 5th Wheel Pin Box
Randy M.
4/15/2026
The Moryde cushion hitch is fantastic! Takes that chucking out on rough roads. Would never want to tow again without one.