Will Trailer Valet JXS Jack Fit on Same Mount as Trailer Valet 5x Swivel Jack

Question

Question:

Will this jack into the mount for the Trailer Valet 5X trailer mover? I’d like to user the trailer mover to get my camper up the slight grade in the driveway to move it into the garage, but swap out for the smaller jack wile on the road.

asked by: Jacob R

0

Expert Reply:

Hey Jacob, yes the Trailer Valet JXS Drill Powered Swivel Trailer Jack w/ Wheel # TV86FR that you reference does fit the same jack mount as the Trailer Valet 5X Swivel Jack # STC-V211 so if this is what you have already then you could swap it into the mount you have already.

expert reply by: Jameson C

0

Answer 1

I wasn't sure exactly what dimension you were looking for on the mounting bracket of the Trailer Valet part #STC-V211 so I attached a picture that has nearly every dimension for you to check out.

view full answer...

Answer 2

I have attached two diagrams below with the dimensions for the XO350 and XO750. Both of these use a bolt on installation so you really only need to know the height of your tongue to see if it is compatible. The #ORJW350D fits 2" to 6" tall…

view full answer...

Answer 3

I spoke with my contact at Ark and he sent me a dimensional drawing of the mounting bracket that the Extreme Off-Road Trailer Jack w/ Dual Wheels #ORJW500D has. The dimensions are in millimeters.

view full answer...

Answer 4

Hey Anthony! The outer diameter of the weld-on pipe coupling on the Trailer Valet JX Trailer Jack #TV35FR is 2.01". I went ahead and attached some dimensional drawings below for your reference. What kind of trailer do you have?

view full answer...

Answer 5

The mounting plate on the ARK Removable Extreme Off-Road Swing-Up Trailer Jack #ARK57FR is 5-1/2" wide and 7-1/2" tall. It is designed with several bolt hole patterns(see image) to fit trailer tongues from 2-6" tall.

view full answer...

Answer 6

Hey Matt, since you have a slight grade I would instead recommend the Trailer Valet 5X part #STC-V211 over the #ORJW1SU. The #ORJW1SU requires releasing tension in the crank that turns the wheel every time you go to crank the wheel further so I would…

view full answer...

Answer 7

When fully retracted, or collapsed the jack is 28.58 inches tall, and 38.42 inches tall when extended as shown in the provided diagram. I've linked you to a product description video featuring the #ORJW1SU ARK Extreme Off-Road Ratcheting Trailer…

view full answer...

Answer 8

The Xtreme Off-Road Ratcheting Trailer Jack w/ Dual Wheels #ARK54FR will hold in place when pushing up the slope. If you're going down the slope the mechanism will not hold it is place, as the wheel is designed to free spin in the direction of…

view full answer...

Answer 9

The collapsed height of the Extreme Off-Road Ratcheting Trailer Jack w/ Wheel #ORJW1SU is 28-5/8" from the base of the wheel to the top of the jack tube. The tallest measurement of the jack when fully extended is 31-15/16" from the center…

view full answer...

Answer 10

I do have an option for you but the Xtreme Off-Road Ratcheting Trailer Jack part #ORJW1SU isn't quite cutout out for what you're wanting. Instead, I recommend the Trailer Valet 5X Swivel Jack and Trailer Mover part #STC-V211 which is rated…

view full answer...

Answer 11

I went to our warehouse and took some measurements of the Trailer Valet 5X, part #STC-V211 for you. I have attached a photo of the #STC-V211 with the dimensions noted. From the top mounting bolt on the mounting bracket to the top of the handle it…

view full answer...

Answer 12

Here is an image I have from the Xtreme Off-Road Swing-Up Trailer Jack #ORJW750D in zinc which will have the same dimensions as the black Jack #ORJW750BD you are looking at.

view full answer...

Will Trailer Valet JXS Jack Fit on Same Mount as Trailer Valet 5x Swivel Jack

Product Page this Question was Asked From

Continue Researching