Mounting Bracket Bolt Hole Dimensions of the Extreme Off-Road Trailer Jack w/ Dual Wheels # ORJW500D

Question

Question:

Hi, can you pls provide the mounting plate dimension for this jack? They seem to be huge and wanted to make sure about the dimensions. Thanks!

asked by: Humprey

0

Expert Reply:

I spoke with my contact at Ark and he sent me a dimensional drawing of the mounting bracket that the Extreme Off-Road Trailer Jack w/ Dual Wheels # ORJW500D has. The dimensions are in millimeters.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Yes, the Extreme Off-Road Swing-Up Jack w/ Dual Wheels iItem #ORJW500D will work for your T@B 400 Tear Drop Trailer. It looks like your trailer comes with an a-frame jack. You would need to ensure you have enough space on your tongue to accommodate…

view full answer...

Answer 2

I have attached two diagrams below with the dimensions for the XO350 and XO750. Both of these use a bolt on installation so you really only need to know the height of your tongue to see if it is compatible. The #ORJW350D fits 2" to 6" tall…

view full answer...

Answer 3

Hey Anthony! The outer diameter of the weld-on pipe coupling on the Trailer Valet JX Trailer Jack #TV35FR is 2.01". I went ahead and attached some dimensional drawings below for your reference. What kind of trailer do you have?

view full answer...

Answer 4

Hey Steve, the schematic that shows the 645 mm measurement is for the #ORJW500D which is the Ark 500 Series Off-Road Jack. The answer that shows the 18" retracted length is referencing the #ORJW350D which is the 350 series jack and is smaller…

view full answer...

Answer 5

Hey Matt, since you have a slight grade I would instead recommend the Trailer Valet 5X part #STC-V211 over the #ORJW1SU. The #ORJW1SU requires releasing tension in the crank that turns the wheel every time you go to crank the wheel further so I would…

view full answer...

Answer 6

I do have an option for you but the Xtreme Off-Road Ratcheting Trailer Jack part #ORJW1SU isn't quite cutout out for what you're wanting. Instead, I recommend the Trailer Valet 5X Swivel Jack and Trailer Mover part #STC-V211 which is rated…

view full answer...

Answer 7

The Xtreme Off-Road Ratcheting Trailer Jack w/ Dual Wheels #ARK54FR will hold in place when pushing up the slope. If you're going down the slope the mechanism will not hold it is place, as the wheel is designed to free spin in the direction of…

view full answer...

Answer 8

When fully retracted, or collapsed the jack is 28.58 inches tall, and 38.42 inches tall when extended as shown in the provided diagram. I've linked you to a product description video featuring the #ORJW1SU ARK Extreme Off-Road Ratcheting Trailer…

view full answer...

Answer 9

The collapsed height of the Extreme Off-Road Ratcheting Trailer Jack w/ Wheel #ORJW1SU is 28-5/8" from the base of the wheel to the top of the jack tube. The tallest measurement of the jack when fully extended is 31-15/16" from the center…

view full answer...

Answer 10

Here is an image I have from the Xtreme Off-Road Swing-Up Trailer Jack #ORJW750D in zinc which will have the same dimensions as the black Jack #ORJW750BD you are looking at.

view full answer...

Answer 11

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Mounting Bracket Bolt Hole Dimensions of the Extreme Off-Road Trailer Jack w/ Dual Wheels # ORJW500D

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching