Is There a Hardware Kit for the Bolt On Atlas IV Double-Acting 10k Hydraulic Trailer Jack
Updated 03/17/2026 | Published 03/15/2026
Products Featured in This Question
Question:
Looking at the Atlas IV Double-Acting Hydraulic Trailer Jack - Bolt On - 10K for my trailer but I will like to see if you guys also have the bolts for it or what kind do you recommend to use. I currently have mine weld on but I will like to use the bolt in now. Thanks for your help
asked by: Luis
Expert Reply:
Hey Luis, welcome back! The Atlas IV Double-Acting Hydraulic Trailer Jack item # ST73FR does not have a specific hardware kit available for it.
You'll need a total of eight Grade 8, 1/2" diameter bolts to complete the installation. The length of the bolts is going to depend on how thick your trailer's frame is so you'll need to measure that and add 3/8" for the bracket thickness. 1/2-20 fine thread grade 8 bolts need 80 – 90 ft-lbs of torque.
I attached a dimensional diagram with the bolt spacing below.
What kind of trailer are you looking to install this jack on?
You can add this information, along with any other questions you have, where it says Add Comment.
(click to enlarge)
Product Page this Question was Asked From
Atlas IV Double-Acting Hydraulic Trailer Jack - 26" Lift - 10,000 lbs - Direct Weld
- Trailer Jack
- Dump Trailer
- Enclosed Trailer
- 5th Wheel Trailer
- Gooseneck Trailer
- Side-Mount Jacks
- 9001 - 10000 lbs
- Hydraulic Jack
- 26 Inch Lift
- Weld-On
- With Rectangle Foot
- Stillwell
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Replacement Rotor for Dexter Disc Brakes - 8 on 6-1/2 - E-Coat - #14 Torflex Torsion Axles
- Shop: etrailer Hydraulic Trailer Jack - Square Tube - External Pump - 20" Lift - 8K lbs - Direct Weld
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector
- Shop: Curt Mounting Bracket for 7-Way Connector Plug
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Kodiak 11" Rotor - Dacromet - 9,000 lbs to 10,000 lbs - AL-KO/Rockwell
- Shop: Replacement Caliper Retaining Shoulder Bolt for Dexter 10,000-lb to 12,000-lb Hydraulic Disc Brakes
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer wiring
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer tires and wheels
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: Clean Up Your Trailer Wiring
- Shop: Suspension Enhancement
- Search Results: trailer jack
- Video: Curt Mounting Bracket for 4-Pole Flat Trailer Connector Review
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Shop: Brake Controller
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Search Results: trailer hitch ball mount
- Shop: Gooseneck Hitch
- Article: How to Choose the Right Trailer Hitch Class
on Trailer Jack
