Is "Super Duty" Imprinted on WeatherTech Custom Fit Hood Protector

Question

Question:

Is "SUPER DUTY" imprinted on the shield?

asked by: Dan

0

Expert Reply:

Hi Dan; the WeatherTech Custom Fit Hood Protector # WT94BF only has the small WeatherTech logo in the corner. This does not have "Super Duty" imprinted on the hood protector.

expert reply by: Robin H

0

WeatherTech Hood Protector
(click to enlarge)

Derek

3/18/2026

Correct - the hood protector will cover the "SUPER DUTY" logo on the hood entirely unfortunately. I just installed these on my '26 F250 Super Duty trucks.

Answer 1

Hey Ralph, the Putco Window Visors part #P45QR that you referenced are in-channel mount like you asked about.

view full answer...

Answer 2

Hello Merle, thanks for reaching out. So we do have an air bag kit that will fit your2024 Ford F250 with the onboard scales, and for that I recommend the Firestone Ride Rite #F35FV. Keep in mind though that the onboard scale basically works by…

view full answer...

Answer 3

When setting the tension for your Solera RV Slide-Out Awning #LCV000163285 you would need to roll the spring/roller tube upwards towards the body of the trailer 12 - 16 times. When looking at it from the right side of the roller tube it would be…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

Hello Matt, I was seeing some mixed information on this as well, so I reached out directly to my contact at Firestone to confirm. The Firestone Ride-Rite Air Bags w/ Easy Mount Compressor - Wireless Control - Single Path - 5,000 lbs #F44XV will fit…

view full answer...

Is "Super Duty" Imprinted on WeatherTech Custom Fit Hood Protector

Continue Researching