Replacement Foot Pads for Lippert Hydraulic Jack 333866

Question

Question:

I need to replace the rear foot pads for the stabilizer jacks. Thor provided Lippert P/N 333866 for the entire assembly. Would Etrailer P/N LC324269 be the correct replacement for the rear stabilizer foot pads?

asked by: David P

0

Expert Reply:

Hey David! Yes, you can use the Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System # LC324269. This is the correct replacement for your Lippert Hydraulic Jack # LC93FC (333866).

Any big trips coming up with your Thor once you get the jack feet replaced?

expert reply by: Robin H

0

Replacement Foot Pad
(click to enlarge)

Answer 1

Hey Brandon! I can certainly help you narrow this down! The Lippert Level Up system has a few different jack configurations, so I want to make sure we get you the correct replacements for your 2026 Georgetown 36F5. First, the difference between the…

view full answer...

Answer 2

Hey Mark! Yes, the Replacement Hydraulic Jack Assembly for Lippert Level Up #LC868NV is the correct replacement for your older 1958614 jack. Lippert also lists it as the replacement for part numbers 19586010 and 2021102037. This is the newer Gen 2…

view full answer...

Answer 3

It sure is Tony. The Replacement Hydraulic Jack w/ Face-Seal Fittings item #LC93FC is indeed the Lippert part number 2024015102. This is a 14,000 lbs capacity GEN 2 hydraulic jack designed for Lippert's Level Up hydraulic leveling systems. The…

view full answer...

Answer 4

We do carry the Replacement Hydraulic Jack Assembly #LC43ED for your Thor 34R class A motorhome. This is the Lippert part number 372892 they gave you.

view full answer...

Answer 5

Hey Mike! The Thetford Aqua-Magic Style II Part-Timer RV Toilet item #TH35SE is going to be about as close of a replacement as you can get for your 42070 model. There is one measurement you're going to want to take to confirm it'll work.…

view full answer...

Answer 6

I attached a wiring diagram for the Kwikee Step Motor Conversion/Upgrade Kit #LC379145 for you to check out but there isn't a pink wire so maybe you are looking at a diagram for a different motor kit.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Replacement Foot Pads for Lippert Hydraulic Jack 333866

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching