Is Rapid Ramp Hinge Kit Available Without Ramps

Question

Question:

Can I buy the Rapid ramps Hinge kit without any ramps. I dont need more ramps, just the hinge kit

asked by: Lee Z

0

Expert Reply:

Hi Lee; at this time the hinge kit is only available with a complete set of ramps like the etrailer RapidRamps 6' Long Bolt-On Trailer Ramps for over 6-1/2' Wide Trailers # e47XV. There are currently no plans to offer the hinges separately, but we will update the product pages if that changes in the future.

expert reply by: Robin H

0

etrailer RapidRamps
(click to enlarge)

Answer 1

Hey Don, yes I can! The Blue Ox Base Plate Kit #BLU66ER is what you need. This is the only base plate kit confirmed to fit the RHO. You mentioned the Falcon, do you have a Roadmaster Falcon tow bar or did you mean to say Roadmaster base plates? If…

view full answer...

Answer 2

Hi Nick; the brackets and index bars for the etrailer RapidRamps #e47XV are not available separately. At this time, the only way we offer them is with the ramps. What are you planning to use the ramps for?

view full answer...

Answer 3

Kevin, since your trailer measures about 72 inches wide (6 feet) inside the rails, you’ll want one of the 5–6-1/2' wide trailer kits, not the over-width versions. The included slide bar / load bar needs to match this width range. From there, the…

view full answer...

Answer 4

Mark, that’s exactly the problem RapidRamps were designed to fix. And I understand the frustration as I currently use 3 foot long heavy angle-iron steel ramps on my Big Tex car hauler. I plan to upgrade to one of these kits. Once you install a…

view full answer...

Answer 5

Hey there Daniel - it really depends on your trailer height and what you’re loading. The 6' RapidRamps kits (part numbers #e47XV for 5–6-1/2' wide trailers and #e67XV for trailers over 6-1/2' wide) give you a gentler approach angle, which…

view full answer...

Answer 6

Yes, they can, Chris. With both 6 foot RapidRamp kits #e47XV and #e67XV, the ramps slide side-to-side along the index bars so you can line them up with different tire widths. Once lifted back in the upright position, they latch in place, and you can…

view full answer...

Answer 7

Aaron, since your trailer falls in the 5 - 6-1/2 foot width range, your two options are the 5' RapidRamps kit #e37XV or the 6' RapidRamps kit #e47XV. For low-clearance equipment like a lawn tractor mower, the 6' kit is usually the better…

view full answer...

Answer 8

Hi Jen! The Yakima OverNOut Awning - Roof Rack Mount - Clamp On - 6' 6" Long x 6' 6" Wide #Y36VR really does need to be installed on a roof rack as there are no adapters available, but I think I have a couple options that may…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Is Rapid Ramp Hinge Kit Available Without Ramps

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching