Will Yakima Overhaul HD Ladder Rack Fit T Slots of BAK Revolver X4TS

Question

Question:

I have the BAK Revolver X4TS that has the T Slots on a Ford F150. Will the Yakima OverhaulHD work with it using the Tonneau Cover Adapter?

asked by: Robert M

0

Expert Reply:

Hey Robert, yes the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack w/ Tonneau Cover Adapters # Y01151-5855 that you referenced will fit the T slots of the BAK Revolver tonneau cover that you have. What are you planning on carrying on the Overhaul?

expert reply by: Jameson C

0

Robert M.

2/5/2026

Hi Jameson. I’m planning on mainly using for kayaks, paddle boards, or canoe. I have seen lots of conflicting information so it’s been quite confusing. Yakima does not call it out as supported. Do you have any examples of it working? Btw, you guys at eTrailer are great! Thanks for the help!

Jameson C.

2/5/2026

@RobertM I was able to find examples online where people were able to make it work. Here's a link to a forum post were someone was able to make it work on a Ford Maverick: https://www.mavericktruckclub.com/forum/threads/bak-revolver-x4s-yakima-overhaul-hd-installed.32525/

Preston

2/6/2026

@RobertM If you purchase the overhaul kit that includes the track mounts, you should be good to go. The Caveats: -the track mounts for the overhaul will require drilling into the top of the bedrails to securely mount the rails. -the rail will sit outside of the tonneau rails, which will push the overhaul mounts a slight bit over the truck bed; which is ultimately an aesthetics decision. I've had the overhaul for a couple of years now and I love it. I use it for work and it's rock solid. My only qualm is that I wish the risers were a little more vertical, instead of canted at the 15 degree angle they are (it limits the width range of my truckbed with I'm stacking tall stuff). two add-onn accessories that make hauling stuff a ton easier are: -https://www.etrailer.com/Ratchet-Straps/CargoBuckle/IMF18800-77.html -https://www.etrailer.com/Accessories-and-Parts/Yakima/Y01161.html hope this helps, and best of luck!

Darrell

2/10/2026

I have the Yakama OH Rack and a Pace Edwards retractable cover on my 2024 Ram 1500. This combination fit my truck perfectly with no drilling. I use the racks along with a set of Malone Seawings to carry my kayaks and canoe. I do remove my racks in winter and hang them on the garage wall. Great combination, I would buy this again!

Jameson C.

2/10/2026

@Darrell Awesome to hear! Glad you like it!

Answer 1

You can definitely use the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack with 68" HD Bars #Y01151-58 for your 2021 Ford F-150, but I don't recommend going with 60". I think you'll be cutting it a little too close plus you want…

view full answer...

Answer 2

The BAK Revolver X4 is not going to work with the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack w/ Tonneau Cover Adapters #Y01151-5855, you'd need to use either the Retrax XR, Ford Embark LS, or the Pace Edwards UltraGroove.

view full answer...

Answer 3

Yes, I confirmed with Yakima that the Yakima Crossbar Pads for Aero Crossbars - 30" Long - Qty 2 #Y07413 will fit on your Overhaul HD crossbars.

view full answer...

Answer 4

If the EndCap for Yakima HD Crossbars #YA54FR keeps falling off then that leads me to believe you may not have the bolt and nut lined up correctly. If you check out the attached photo you'll see where the nut is supposed to sit on the endcap.…

view full answer...

Answer 5

Yes, TS Rails like the #TH75FR are compatible with both the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack for Tonneau Cover - 60" Crossbars #Y01151-5755 and a BAK Revolver X4S cover like the #BAK24ZR. If you could provide me with the…

view full answer...

Answer 6

The Universal Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob #331-TPSI-001 is going to require a 1" diameter hole in order for it to fit in your blank panel spot. The face of the panel is approximately 1-1/16" wide…

view full answer...

Answer 7

The BAKFlip MX4 Hard Tonneau Cover installs inside the bed rails so you can use a ladder rack which mounts in the stake pockets. The way the ladder rack must install it doesn't give you many options. There are two I recommend looking at and the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Will Yakima Overhaul HD Ladder Rack Fit T Slots of BAK Revolver X4TS

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching