Will the Set Screws Sit Flush on the 3" Gen-Y Anti-Rattle Reducer Sleeve?
Updated 01/28/2026 | Published 01/02/2026
Products Featured in This Question
Question:
are the set screws on this adapter flush/recessed when tightened? i ordered the 2.5inch Gen-Y 9inch for my 2020 Newmar superstar 4051 and the rig receiver is 3. however my blue-ox Apollo is a 2.5inch shank so i dont want a 3inch hitch. also, aside from a reducer, is there a 3inch shank to 2.5inch receiver hitch setup that i could utilize for the tow bar? i am towing a 2022 ram 2500 with a golf cart in the bed.
asked by: Ed K
Expert Reply:
Hey Ed, welcome back! The set screws will definitely be flush when you use the Gen-Y Anti-Rattle Reducer Sleeve item # GY22YR. The sleeve is going to be held on securely with those screws to your Blue Ox Apollo item # BX7470. I attached a picture below so you can see how it'll look installed.
The only extenders we have that fit a 3" receiver are the TorkLift Cannon Hitch Extension like item # TLE1636. However, they're designed specifically for the Ford factory 3" hitch. They're not rated for non-Ford hitches due to the support chains and how they're required to be setup. Other than that the only hitch extenders I have for a 2-1/2" receiver reduce down to 2" like the item # C45048 or item # e53YR. Even the High-Low adapters like item # RM-058-4 that fit a 2-1/2" receiver drop down to 2".
If you have any additional questions, go ahead and click on the box that says Reply to Jerred H and I'll be happy to answer them.
(click to enlarge)
Product Page this Question was Asked From
Gen-Y Hitch Anti-Rattle Reducer Sleeve - 3" to 2.5" Trailer Hitch
- Hitch Adapters
- Hitch Reducer
- No Extension
- Fits 2-1/2 Inch Hitch
- 3 Inch to 2-1/2 Inch
- Gen-Y Hitch
more information >
Continue Researching
- Search Results: motorcycle tie downs
- Search Results: motorcycle
- Video: Review of Z-TRAK E Track - Wheel Chocks 2-Bikes - ZT69FR
- Search Results: pintle hitch
- Search Results: pintle ring
- Shop: ShockStrap Ratchet Motorcycle Tie-Downs w Shock Absorbers - 1-1/2" x 7' - 1,000 lbs - Qty 4
- Shop: Z-TRAK Moto-Chok Fat-Tire Bike Chocks - 2 Bikes
- Shop: Z-TRAK Secure Anything Bundle w/ Anchors, Clip Rings, Bungee Strap
- Shop: Z-TRAK High-Strength E-Track Tie-Down Rail - 36" Long
- Shop: Z-TRAK Low-Profile Moto-Chok Bike Chocks - 2 Bikes
- Search Results: utility trailer accessories
- Search Results: atv
- Search Results: tire only trailer tires and wheels
- Shop: TorkLift Tie Downs - Custom Frame Mount - Front and Rear
- Shop: TorkLift GlowStep Camper Scissor Steps - 3 Steps - Aluminum - 20" Wide - 375 lbs
- Video: All About the ShockStrap Ratchet Motorcycle Tie-Downs w Shock Absorbers
- Video: Let’s Check Out the ShockStrap Ratchet Tie-Down Strap w Shock Absorber
- Q&A: Recommended Hitch Extender for Towing/Hitch Accessories With Truck Bed Camper
- Video: DIY 2020 Ford F-250 Super Duty Installation for the TorkLift Tie Downs
- Video: Review of the Snap-Loc E Track Tie-Down Anchor
- Video: ShockStrap Tie-Down Straps Manufacturer Demo
- Video: Timbren Trailer Suspension - Leaf Spring Suspension - TTRA1702 Review
- Shop: Camper Tie-Downs
- Q&A: Radial 4.80 X 12 Trailer Tire Rated For Speeds At Least 75MPH
- Q&A: How To Add Towed Vehicle Battery Charge Line Kit To Setup With 4-Way
- Q&A: Correct Length of Breakaway Cable for my Artic Fox 22G
- Q&A: Is There an RV Roof Vent Assembly that Can be Thermostatically Controlled
- Q&A: Which Direction Does The TowSmart Hitch Receiver Reducer Sleeve TS75FR Go?
- Q&A: Does Weigh Safe 180 Hitch 2-Ball Mount Come With Hitch Pin
- Article: Snow Tire Chain Overview: How to Buy the Right Tire Chains
on Hitch Adapters
Jerred H.
1/27/2026
Hey Ed, how did the Gen-Y anti-rattle reducer sleeve work out with your Blue Ox Apollo setup? Did the set screws sit flush like you were hoping? Your feedback could really help others trying to match a 3-inch receiver with a 2.5-inch tow bar.