Replacement Renewable Seat for Phoenix Faucets Bathroom Faucet

Question

Question:

I have the Replacement Compression Stem for Phoenix Faucets Dual Handle Bathroom and Garden Tub Faucets - Part Number: PF284007 what replacement brass valve seat do I need for this item

asked by: Daniel H

0

Expert Reply:

Hi Daniel; the part you need is the Replacement Renewable Seat for Phoenix Faucets Dual-Handle Bathroom and Kitchen Faucets # PF187015.

expert reply by: Robin H

0

Replacement Renewable Seat
(click to enlarge)

Robin H.

12/29/2025

Hey Daniel, did the replacement renewable seat work well with your Phoenix faucet setup? Knowing how it fit with the compression stem could help others working on the same repair.

Answer 1

It sure is Cheri. The Replacement Compression Stem item #PF284007 is the correct one for your Phoenix Prod pn: 61-5. It can indeed be used to replace both the hot and cold stems on your shower handle. The item #PF284007 is a replacement compression…

view full answer...

Answer 2

Hey Kenny, the correct replacement seats to use with the Replacement Diverter Stem part #PF184007 is the part #PF284008. What RV do you have this faucet installed in?

view full answer...

Answer 3

I went out to the warehouse and found that part #PF187016, part #PF284003, and part #PF284008 all measure the same. When I called my contact at Phoenix Faucets she said that they were all actually the same part number they are just packaged slightly…

view full answer...

Answer 4

Hey Gary, the correct replacement renewable seat for the Compression Stem #PF284007 that you referenced is the part #PF187017 actually.

view full answer...

Answer 5

We have the Replacement Compression Stem for Phoenix Faucets Dual Handle Bathroom and Garden Tub Faucets #PF284007 which is a replacement compression stem and bonnet that measures 1-3/4" long and has a 1" diameter for either the cold or hot…

view full answer...

Answer 6

For the size and thread you are looking for you need the #PF187017 and you'd be set. I attached a dimension picture that shows it's length as well.

view full answer...

Answer 7

In order to find replacement parts for your current faucet we'd need to know the brand and model number. With you having a mobile home I doubt they used any RV industry parts as there's typically a higher cost over residential components. If…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Replacement Renewable Seat for Phoenix Faucets Bathroom Faucet

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching