Fuse Location for Trailer Brake Controller on a 2005 Chevy Silverado 1500

Question

Question:

where is the fuse located electris brake for chevrolet pickup 2005 1500

asked by: Randy H

0

Expert Reply:

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have included a picture that should help. I have also linked an article that will also help.

expert reply by: Michael H

0

click to enlarge

Answer 1

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 2

The connections you will need to make to install your Voyager brake controller are listed below. If your Voyager has a connector attached to the wires at the back you can use the Pigtail Wiring Harness, #7894, to connect to the wires on the connector…

view full answer...

Answer 3

The brake controller port on your 2005 GMC Yukon Denali will be located in the black junction box, which is under the dashboard and to the left of your steering column, right above the carpet. The plug in point will be the second port from the left,…

view full answer...

Answer 4

We have everything you'll need to add brakes to your cargo trailer but since we don't know exactly what axles you have you'll have to check out your setup and take a few measurements to determine what exactly you'd need to install…

view full answer...

Answer 5

A factory 7-way trailer connector isn't all you need to power a trailer's electric brakes. You still need a brake controller. Some Ford F-150s are equipped with a factory integrated brake controller, which you may have. If your 2012 Ford…

view full answer...

Answer 6

Dexter 8-249 hubs normally have inner bearings like Item #L68149 and outer bearings like Item #L44649. If these are your bearings (the size will be stamped on them) then it sounds like you need Trailer Hub and Drum Assembly Item #84556UC3 by Dexter…

view full answer...

Answer 7

Under the hood of the 2004 Chevrolet pickup there are two power posts located at the power distribution box, see photo at right. The most forward power post is the one that is used for supplying power to the 7-Way connector at the rear of the…

view full answer...

Answer 8

It makes sense....sort of. The trailer brake circuit won't be active on your tow vehicle unless you have a brake controller - even with a factory tow package. What I'm guessing they meant by this is that a brake controller will send a small…

view full answer...

Answer 9

To install the P2, part #90885 brake controller in your Touareg you will need to do some hardwiring. If you do not have a 4-way connector at the rear of your Touareg you will need to install a trailer wiring connector like part #118668. You will then…

view full answer...

Answer 10

The fuse that controls the brake controller power circuit under the hood of your 2005 GMC Sierra is labeled ETC/ECM which I pointed out in the attached picture.

view full answer...

Answer 11

Sometimes the fuses are already installed from the factory on a 2008 Chevy Silverado when installing a brake controller, but if not the fuse slots are in the front of the box. I have attached a picture that shows the location of fuse slots. I have…

view full answer...

Answer 12

It looks like on pages 5-126 and 5-127 or your owner's manual there is the TBC BATT fuse in the fuse box that is under the hood. This is called the Truck Body Controller Battery Feed and looks to be the only fuse title that might affect the…

view full answer...

Fuse Location for Trailer Brake Controller on a 2005 Chevy Silverado 1500

Featured Help Information

Miscellaneous Media

Continue Researching