Replacement Sidewind Gear Kit for a Bulldog 190754 Jack

Question

Question:

Bulldog 190754 jack Need replacement gear kit

asked by: Michael M

0

Expert Reply:

Hey Michael, thanks for the information! For a Bulldog item # BD190754 jack you'll need the Replacement Gears for Bulldog Sidewind Trailer Jacks item # BD5002581360.

What kind of trailer do you have?

expert reply by: Jerred H

0

Jerred H.

10/30/2025

Hey Michael, how did the replacement gear kit work out with your Bulldog jack? Your update could make it easier for the next person needing the same repair.

Michael M.

10/30/2025

@JerredH no, wrong kit, this was supposed to work with bulldog 190754 but gears were too small and both same size, the actual gears needed are 2 different size gears and the one that lays flat is larger.

Jerred H.

11/1/2025

@MichaelM Replacement Gears for Bulldog Sidewind Trailer Jacks with 5,000-lb Capacity item # BD5002581360 is the one that Bulldog lists on their website.

Answer 1

For your 2006 Ford F-250, with the Aries ActionTrac Motorized Running Boards with Custom Installation Kit #AA3025183, the correct replacement mounting kit is the Custom Mounting Kit for Aries ActionTrac Motorized Running Boards #AA3025124.

view full answer...

Answer 2

Hi Damon! We do have a replacement handle for the Bulldog Square Jack #BD180455 with the #BD800144, but it is just a standard handle. We don't have a way to motorize the #BD180455, unfortunately. You could cut the handle down and make it so a…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Replacement Sidewind Gear Kit for a Bulldog 190754 Jack

Continue Researching