Parts Needed to Flat Tow a 2018 Jeep Wrangler Unlimited Sahara Behind a 2019 Fleetwood Bounder

Question

Question:

Can my RV 2019 fleetwood bounder 35K with 5K hitch towing capacity tow a 2018 jeep wrangler sahara unlimited 4 door safely. Do towing components add to 5K limit?

asked by: Robert

0

Expert Reply:

Hey Robert. The Ford F-53 chassis your 2019 Fleetwood Bounder 35K was built on has a 8,000 lbs towing capacity so you'll be good. It looks like a 2018 Jeep Wrangler Sahara weighs around 4,400 lbs so you won't be over capacity for that hitch. There's nothing you can add to increase the towing capacity of your Bounder or hitch.

Here's the parts you'll need to flat tow a 2018 Jeep Wrangler Unlimited Sahara:

Tow Bar and Safety Chains - etrailer SD Non-Binding Tow Bar for Roadmaster Direct-Connect Base Plates item # e74ZR

Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit - Removable Arms item # RM-521453-5

Wiring Harness - Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit item # RM-15267

Supplemental Braking System - Demco Stay-IN-Play Duo Braking System for RVs w/ Hydraulic Brakes item # DM86VR.

High Low Adapter - The tow bar needs to be within 3" of level. If you measure the height of the inside top of the hitch receiver tube on your RV, and the height difference is more than 3 inches above/below the base plate tab height, you'll need a high/low adapter. I have linked a FAQ article that explains all this in more detail along with our selection of adapters.

Have you flat towed a vehicle before or is this going to be your first time?

expert reply by: Jerred H

0

Direct-Connect Base Plate Kit
(click to enlarge)

Robert

10/16/2025

Jarred, I require a 4" drop so need a high/ low adapter. Do you recommend getting a dual hitch adapter in case I need to install a bike rack etc behind motorhome? Robert

Reply

Jerred H.

10/20/2025

@Robert I would, especially since you know you need a high low adapter anyways. The Roadmaster Dual Hitch Receiver Adapter item # RM83SR has a 4" drop and it will work great if you decide to attach a bike rack at some point.

Reply

Answer 1

Based on your dimensions you'd need 7 inches for your tow bar to be totally level. So since there's only a 6 inch and an 8 inch high low adapter the better choice is to have the sitting slightly higher on the RV side. If a tow bar pulling…

view full answer...

Answer 2

I checked with Lippert and the part number you have of 1510000140 corresponds with the Revolution Kwikee step and the replacement control module you need then is the part #LC363985.

view full answer...

Answer 3

I checked with Lippert and the part number you mentioned corresponds with the Revolution Kwikee step and the replacement control module you need then is the part #LC363985.

view full answer...

Answer 4

The Kwikee Control Box #909506000 has been discontinued by the manufacturer. The replacement part is determined by the date of manufacture which you can determine by looking at the current part which will have a date on it. If not, you can supply the…

view full answer...

Answer 5

I checked with Lippert and the part number you have of 1510000140 corresponds with the Revolution Kwikee step and the replacement control module you need then is the part #LC363985.

view full answer...

Answer 6

The correct replacement part for your Revolution Kwikee step P/N 1510000140, is the: -Replacement Control Unit for Kwikee 40 Series Electric RV Steps #LC363985. I have included an installation video, preformed on a 2016 Newmar Ventana LE.

view full answer...

Answer 7

The correct replacement control unit for your Kwikee 1510000140 Rev 0B steps is part #LC363985. We have confirmed this fitment with Lippert. Attached is an installation video for you to check out on a different motorhome.

view full answer...

Answer 8

The 334850 part number you mentioned refers to the Replacement Control Switch #LC334850. This particular unit replaces the control switch assembly for certain Lippert Tread Lite RV Steps ( #LC353542, #LC353543, #LC353620, or #LC353621).

view full answer...