Can I Install a T-Fitting on the Air Lines for the Air Lift LoadLifter 5000?

Question

Question:

Can you install a T-fitting in the air lines so you can air both bags simultaneously?

asked by: Bruce B

0

Expert Reply:

Yes, you can Bruce! This is a common practice actually. You can use the Air Lift Union Tee for 1/4" Air Lines item # AL21838. This will allow you to fill both bags using a single inflation valve.

The Air Lift LoadLifter 5000 Air Helper Springs item # AL57204 are confirmed to fit your 2017 GMC Sierra 1500 and are compatible with in bed hitches.

How long is your truck bed? Some of these kits are specific to the bed length for the 2018 Sierra 1500s.

expert reply by: Jerred H

0

Union Tee
(click to enlarge)

Bruce B.

10/13/2025

Crew cab w/ 70" inch bed

Jerred H.

10/13/2025

@BruceB Thanks for the information! The Air Lift LoadLifter 5000 Air Helper Springs item # AL57204 are the right ones for your truck.

Answer 1

Hey Dan! It looks like the lift in the back of the 2021 Ford F-150 Tremor only has a 2" lifting block. You will not need any spacers to install the Air Lift LoadLifter 5000 Ultimate Air Helper Springs item #AL54JQ.

view full answer...

Answer 2

Hey Raymond, since the 5k rated etrailer jack part #e55ZV is rated higher than the 3.5k option you also mentioned it will work a little bit quicker since it won't be working quite as hard. With that said it's not a fast jack by any means. It…

view full answer...

Answer 3

If they were talking about the hub face and spring center measurements then what was referred to was the hub-face-to-hub-face and spring-center-to-spring-center lengths. Hub face is measured from the base of one wheel stud to the base of the wheel…

view full answer...

Answer 4

Hello Nathaniel, thanks for reaching out. So the etrailer jacks are going to be a great choice from a durability and affordability standpoint. The jacks offer all of the features you would want like a work light, sealed switches and a manual crank…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Kent! Your Alliance Avenue already has some great suspension components with the MORryde CRE3000 equalizers, wet bolt kit, and Rota-Flex pin box. I wouldn't replace any of those unless you're experiencing a specific problem. The next…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Can I Install a T-Fitting on the Air Lines for the Air Lift LoadLifter 5000?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching