Diagram of the Dexter Self-Contained Hydraulic Jack- Square Tube DX72CR
Updated 08/26/2025 | Published 08/21/2025
Question:
I have a few questions about the Dexter hydraulic jack partDX72CR dimensions. What are the dimensions of the mounting plates? What is the distance from center to center of the plates? What are the dimensions of the hole pattern on the mounting plates, as well as the diameter of the holes? What is the distance from the bottom of the stand to the center of the bottom mounting plate?
asked by: Cody W
Expert Reply:
Hey Cody. I have attached a diagram below for the Dexter Self-Contained Hydraulic Jack- Square Tube -item # DX72CR. It has every measurement we have for this jack.
What kind of trailer are you looking to install this on?
(click to enlarge)
Product Page this Question was Asked From
Dexter Self-Contained Hydraulic Jack - Square Tube - 20" Lift - 10,000 lbs - Bolt On
- Trailer Jack
- Dump Trailer
- Enclosed Trailer
- 5th Wheel Trailer
- Gooseneck Trailer
- Side-Mount Jacks
- 10001 lbs or More
- Hydraulic Jack
- Bolt-On
- With Rectangle Foot
- Dexter
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Dexter Self-Contained Hydraulic Jack - Square Tube - 20" Lift - 10,000 lbs - Bolt On
- Search Results: gooseneck hitch
- Search Results: trailer breakaway kit
- Shop: Trailer Hitch
- Search Results: hydraulic jack
- Shop: Trailer Wiring
- Search Results: dexter hydraulic jack
- Video: Review of Dexter Trailer Jack - Self-Contained Hydraulic Jack - DX72CR
- Search Results: receiver hitch
- Shop: etrailer RapidRamps 6' Long Bolt-On Trailer Ramps for over 6-1/2' Wide Trailers
- Search Results: roadmaster battery disconnect
- Shop: Dexter Double-Acting Hydraulic Trailer Jack System - 20" Lift - 10,000 lbs - Direct Weld
- Shop: Bigfoot Tandem Hydraulic Trailer Jack Set - Single Pump - 24" Lift - 20,000 lbs - Bolt On
- Search Results: fits 1~1/4 inch hitch trailer hitch ball mount
- Video: How to Install the Curt Trailer Hitch Receiver on a 2021 Volvo XC90
- Q&A: What Other Parts Are Needed To Install The Dexter Self-Contained Hydraulic Jack DX72CR
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Roadmaster Battery Ace Battery Disconnect w/ Key Fobs - Gas Only
- Video: Setting up the etrailer Trailer Hitch Receiver on a 2023 Honda Odyssey
- Shop: Bright Way 12V Onboard Battery Charger for Hydraulic Dump Trailers AC to DC - 12V - 10 Ah
- Q&A: Depth of Dexter Hydraulic Jack from Bracket To Outer Edge of Pump Enclosure
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2020 Mazda CX-5
- Video: 2020 Mazda CX-5 etrailer Trailer Hitch Receiver: Complete Installation
- Shop: Salt Spreader
- Shop: Brake Controller
- Video: How to Install the Curt T-Connector Vehicle Wiring Harness - 2015 Audi Q5
- Video: DIY Install: Curt Trailer Hitch Receiver on your 2016 Audi Q5
- Shop: Roof Rack
- Q&A: Can The Dexter Self-Contained Hydraulic Jack DX72CR Be Welded On?
- Q&A: Recommended Fluid For The Dexter Self-Contained Hydraulic Jack # DX72CR
on Trailer Jack
Cody W.
8/26/2025
This is perfect, thank you Jerred. I'm looking at installing it on a drop trailer, specifically a Meridian Archer Trailer.