Where Does the Blue Wire Go on the Dexter DX7.5L A-60 Actuator?

Question

Question:

The actuator has a blue and white wire, does the blue go to reverse and white to ground?

asked by: Frank

0

Expert Reply:

Hey Frank, welcome back! The blue wire on the Dexter DX7.5L A-60 item # DX29FR connects to the reverse light circuit of your trailer's wiring harness. The white is the ground wire.

What kind of trailer do you have?

expert reply by: Jerred H

0

Jerred H.

9/2/2025

Hey Frank, did connecting the blue wire to the reverse light circuit and the white to the ground work for your trailer? I’d like to hear your outcome because it could give others confidence when setting up their wiring.

Answer 1

Hey Mickey, We definitely have an surge brake actuator that is going to work for you. I do not have a database that supplies me with what is put on what trailer, in my research I found that most 2009 Rangers have the TDE LP75 which makes sense…

view full answer...

Answer 2

Hello Jarrod, thanks for reaching out. The main difference between the Dexter #DX29FR and #DX89FR is how they attach to the trailer tongue. Each will fit a 3" wide tongue. The #DX29FR is designed to bolt onto the end of the tongue, whereas the…

view full answer...

Answer 3

DOT5 brake fluid is what you'd want to use in the Dexter surge actuator part #DX89FR. If the breakaway pin was pulled it would be replaceable. The breakaway cable is replaceable.

view full answer...

Answer 4

How long of a line do you need? Do you know what size you need? The most common size is 3/16 inch like part #BH-3MFS-4-5 which is 54 inches long.

view full answer...

Answer 5

When looking for a replacement brake line kit, you will want to measure from the port on the back of the actuator to the T-Fitting where the lines split off and go to the separate brakes, which is typically right at the axle. There will be a short…

view full answer...

Answer 6

Thanks for the photos of your trailer! To manage the excess length of the Kodiak Hydraulic Brake Hose #bh-3mgs-18 you can certainly coil up the excess and secure it with a zip tie. Another option is to route the hose along the trailer so that the…

view full answer...

Answer 7

I definitely understand how safety chain capacities and determining exactly what chain rating you need for your trailer can be a bit confusing. To keep it as simple as possible, safety chain requirements state that the breaking strength of EACH…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Where Does the Blue Wire Go on the Dexter DX7.5L A-60 Actuator?

Product Page this Question was Asked From

Continue Researching