Most Common Trailer Brake Line Fitting Size

Question

Question:

I need a brake hose for my boat trailer. tracker boat, trail star trailer, manufactuer- Fabrique par, tracker marine. ser. 4TM14UG244B001006 YEAR 2003 HELP IF YOU CAN THANKS

asked by: Mike

0

Expert Reply:

How long of a line do you need? Do you know what size you need? The most common size is 3/16 inch like part # BH-3MFS-4-5 which is 54 inches long.

expert reply by: Jameson C

0

Answer 1

Hey Mickey, We definitely have an surge brake actuator that is going to work for you. I do not have a database that supplies me with what is put on what trailer, in my research I found that most 2009 Rangers have the TDE LP75 which makes sense…

view full answer...

Answer 2

Hello Jarrod, thanks for reaching out. The main difference between the Dexter #DX29FR and #DX89FR is how they attach to the trailer tongue. Each will fit a 3" wide tongue. The #DX29FR is designed to bolt onto the end of the tongue, whereas the…

view full answer...

Answer 3

Hey Frank, The Kodiak Hydraulic Brake Hose - 3/16" Male Fittings w/ Stainless Flares - 1/8" ID - 15' #bh-3mfs-15 is the only hose we have with the same fitting sizes that falls within your 12-15 foot needed length. This hose is a bit…

view full answer...

Answer 4

Hey Jeff! I saw you bought the DeeMaxx Hydraulic Brake Line item #DE74JR but that doesn't tell me what size your bleeder valve is. Depending on what size your bleeder valve is you'll most likely need a 1/4" or 3/16" ID piece of…

view full answer...

Answer 5

The DB-42 is an older style of UFP 3,500 lb axle disc brake components. The Kodiak kits like the part #K2HR35D will fit in replacement of that and would be an upgrade so this would be a great solution. It comes with everything you'd need to…

view full answer...

Answer 6

Typically trailers will carry more of their weight on the front of the trailer, so you would want to put the brakes on the front axle as it will most likely carry more weight while braking. Also, when braking, weight will shift forward from the…

view full answer...

Answer 7

Hey Frank, welcome back! The blue wire on the Dexter DX7.5L A-60 item #DX29FR connects to the reverse light circuit of your trailer's wiring harness. The white is the ground wire. What kind of trailer do you have?

view full answer...

Answer 8

The Dexter Brake Actuator part #099-175-20 replaced the Titan 60 that has a master cylinder with a fitting at the end. The fitting is a 3/16 inverted flare where the brake lines connect to. You do not need an extra fitting when you use the actuator.…

view full answer...

Answer 9

Your Dico brake assemblies are 10 inch by 2-1/4 inch so the part #T4423400 and #T4423500 would both work as replacements. There is quite a bit of overlap between Titan and Dico parts.

view full answer...

Answer 10

According to my research, the Dico 15638 Braking Assemblies that you have now are 10" x 2-1/4" therefore the correct replacement for you will be the Hydraulic Brake Kit part #AKUBRK-35-D for single servo or part #AKFBBRK-35-D for free…

view full answer...

Answer 11

The Dico 15638 is a 10 x 2-1/4 inch brake drum/hub that used kind of an oddball bearing setup, inner bearing LM67048 and 3/4 outer bearing LM11949. None of the hub/drums we currently carry are compatible with this bearing set. If the drums are still…

view full answer...

Answer 12

Though you can definitely go with the all flexible line kits, like the Kodiak Hydraulic Brake Line Kit #15SI-BLKIT, I do prefer the more traditional steel kits, like the HydraStar Hydraulic Brake Line Kit #HS496-251. I have found the steel line to be…

view full answer...

Most Common Trailer Brake Line Fitting Size

Product Page this Question was Asked From

Continue Researching