What Size Leaf Springs Will The CE Smith Hanger Kit CES32WR Use?

Question

Question:

What leaf spring width do the support?

asked by: Paul

0

Expert Reply:

Hi Paul!

The Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 1-1/4" Rear # CES32WR will fit the standard 1-3/4" double eye leaf springs. There are a few other sizes of double eye springs, but they are extremely uncommon.

What are you wanting to install this on? And, do you already have leaf springs you will be using?

expert reply by: Lazer S

0

Lazer S.

9/2/2025

Hi Paul, Did you decide on what you want to install the hanger kit on, and do you already have the leaf springs you'll be using? I'm here to help if you need any further assistance.

Answer 1

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 2

Start off by placing your axle about 2/3rds of the way behind your trailer coupler. From there you'll need to fine-tune your axle placement until your trailer tongue weight is 10 - 15% the overall weight of your trailer. There isn't a set…

view full answer...

Answer 3

In the attached diagram the A measurement is actually the distance from the center of the spring hangers for a single axle trailer. The spring eye to spring eye measurement for your leaf springs will be slightly different. The B measurement that you…

view full answer...

Answer 4

We have kits for that but you would need to know the diameter of your axles to determine which kit you would need. If the axle diameter is 2-3/8 inch which is common for 3,500 lb axles the kit you would need is the part #K71-384-00. If instead you…

view full answer...

Answer 5

Moving a trailer axle from being overslung to underslung really isn't a big ordeal. It's basically just welding on a new spring seat on the other side of the axle and then using the hardware upside down. We sell kits for this. The diameter of…

view full answer...

Answer 6

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 7

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

What Size Leaf Springs Will The CE Smith Hanger Kit CES32WR Use?

Product Page this Question was Asked From

Continue Researching