Looking For Replacement Brake Shoes For Dexter 10" x 1-1/2" Manual Adjust Electric Brake Assembly

Question

Question:

Im looking for Dexter 10×1 1/2 manual adj. brake shoes Ty

asked by: Stan

0

Expert Reply:

Hello Stan, thanks for reaching out. We do carry the replacement brake shoes for the Dexter 10" x 1-1/2" manual adjust electric brake assemblies. For that you can use part # bp04-065. This will work as long as your brake assemblies were manufactured after 1999.

expert reply by: Jesse M

0

bp04-065
(click to enlarge)

Jesse M.

9/2/2025

Hey Stan, did the replacement brake shoes work for your Dexter brakes? I'm asking because your experience could help others with similar brake assemblies.

Stan

9/4/2025

@JesseM Perfect replacement

Jesse M.

9/4/2025

@Stan Great! Glad to hear that. Come back anytime you need anything!

Answer 1

Hey Robert, so the 5 on 4-3/4 inch bolt pattern is not super common so that is why we only have a silver option that is 15 inch diameter with the part #AM38NR.

view full answer...

Answer 2

Hi Julie, UC3 is added on to this part number because we offer parts with the same part numbers from multiple manufacturers so a code or extra numbers get added on to differentiate the parts. If you scroll down on the #8-388-80UC3 page you'll see…

view full answer...

Answer 3

If you have the old bearings and seals, it is possible to find the part numbers stamped into them. If these do not have numbers or if they have worn off over time, you will need to take some measurements. I recommend using a digital caliper like the…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Looking For Replacement Brake Shoes For Dexter 10" x 1-1/2" Manual Adjust Electric Brake Assembly

Product Page this Question was Asked From

Continue Researching