Where on Equal-i-zer Weight Distribution System Should be Lubricated
Published 07/10/2025
Products Featured in This Question
Question:
Have a Equalizer 90-00-1000 Manual says to lubricate friction points. Should I disassemble to clean and lubricate all the arm socket surfaces or just clean and lub what is exposed? Thanks, Vic
asked by: Vic M
Expert Reply:
Hey Vic, so the lubricant you need to use is the Equal-i-zer part # EQ91-00-4250 as otherwise if you use anything else you will completely eliminate the anti-sway function of the system as it does require friction.
Cleaning and then lubricating is a solid plan. If it's not too dirty then cleaning may not be as needed but it really comes down to the current condition. I attached a picture on where to lubricate but you can also lube the L-brackets where the bars attach and also the hitch ball.
(click to enlarge)
Product Page this Question was Asked From
Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 10,000 lbs GTW, 1,000 lbs TW
- Weight Distribution Hitch
- WD With Sway Control
- Trunnion Bar
- Fits 3 Inch Frame
- Fits 4 Inch Frame
- Fits 5 Inch Frame
- Fits 6 Inch Frame
- Includes Shank
- Top-Mount
- Fits 2 Inch Hitch
- Allows Backing Up
- 800 lbs
- 900 lbs
- Equal-i-zer
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Keyed Alike Hitch Pin Lock for Replacement Shank for Gen-Y Adjustable Ball Mount 325-GH-306
- Q&A: What Type of Hardware Should be Used to Install Brophy Rope D-Ring Tie-Down Anchor # SS15-C
- Q&A: Which Weight Distribution System is Best for Sway Control
- Video: Brophy Rope D-Ring Tie-Down Anchor Review
- Shop: Equal-i-zer High-Performance Lubricant - 4 oz
- Q&A: Can etrailer Anti-Rattle Hitch Collar Work When Towing Travel Trailer
- Q&A: Does the etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers Have a Weight Limit?
- Shop: Equal-i-zer Weight Distribution w/ 4-Point Sway Control - No Shank - 10,000 lbs GTW, 1,000 lbs TW
- Shop: Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 10,000 lbs GTW, 1,000 lbs TW
- Video: Choosing the Right Anti-Rattle Hitch Device
- Video: A Closer Look at the etrailer Anti-Rattle Hitch Collar on a 2023 Fleetwood Discovery LXE Motorhome
- Video: Let’s Check Out the Blue Ox Hitch Receiver Immobilizer II
- Shop: Blue Ox Hitch Receiver Immobilizer II - 2" Hitches
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Shop: Brophy Rope D-Ring Tie-Down Anchor - Bolt-On - 2-1/4" Wide - Surface Mount - 1,600 lbs
- Search Results: ball covers
- Search Results: lubricants sealants adhesives
- Search Results: hitch covers
- Q&A: Availability of Tie Down Anchor that Mounts Flush on Mounting Surface
- Q&A: Could Brophy Rope D-Ring Tie-Down Anchor SS15-C Be Used with 3/4 inch Plywood
- Shop: Backing Plate for Brophy D-Ring Tie Down Anchor - Black Powder Coat - Qty 1
- Video: Review of the Convert-a-Ball Cover for Interchangeable Shank
Vic M.
7/10/2025
My main question was: Do I disassemble so I lubricate the top and bottom plates of the head, or just the exposed surfaces?