What Frame Dimensions Trailer Valet jack part # TV83FR Fits

Question

Question:

What is the total frame dimensions height that the jack will fit? Thank you. Mike

asked by: Mike V

0

Expert Reply:

Hey Mike, the Trailer Valet jack part # TV83FR that you referenced can fit trailer frames that are up to 8 inches tall and 5 inches deep. What are your frame dimensions?

expert reply by: Jameson C

0

Jameson C.

9/2/2025

Hey Mike, did you get a chance to measure your frame dimensions to see if the Trailer Valet jack will fit? If you’re still looking for a solution, I’m happy to help.

Answer 1

Hey Rebecca! Information is limited and isn't finalized yet from Trailer Valet since the #TV83FR is still a preorder. However, I was able to find that the full height of the jack when it is retracted is 33" from the wheels to the top. I also…

view full answer...

Answer 2

Hello Jason, The Trailer Valet Adjustable Drill Powered Square Jack - 3,000 lbs #TV83FR can work on a 2017 Airstream Tommy Bahama Travel Trailer, as long as a couple of things are confirmed first. The 3,000 lb lifting capacity is generally sufficient…

view full answer...

Answer 3

Hi Dan; there is no specific drill recommended for Trailer Valet jacks like the #TV36FR. Any reputable brand like DeWalt or Milwaukee would be a good option. Battery sizes vary even on the same models so the largest battery available would make the…

view full answer...

Answer 4

Hey Jason, You can use this jack, but there is not a way to attach the Trailer Valet Jack #TV83FR to your welded snap ring mount. You'll either need to use the included wrap around frame bracket to attach this jack to your trailer, or stick with…

view full answer...

Answer 5

Hi Robert, I made a quick diagram of the Trailer Valet JXS Drill Powered Swivel Trailer Jack #TV76FR linked below with the measurements you asked for. It is pretty crude (I am definitely no artist), but I think it gets the point across. Basically you…

view full answer...

Answer 6

Hey Mark, welcome back and thanks for the picture! The Trailer Valet Adjustable Drill Powered Square Jack item #TV83FR will indeed work on your 3-1/2" tongue if you use longer bolts. It's designed for frames up to 6" tall so you'll…

view full answer...

Answer 7

Hi Scot! All the jacks we carry use a bushing for the wheel to rotate on. I am not aware of a jack that uses a bearing for this function, though there could be an option out there. The closest we have to something like that is the Ark Xtreme Off-Road…

view full answer...

Answer 8

I sure do Steve! To replace your Triton boat trailer's jack, I recommend our etrailer Sidewind Aluminum Jack with Wheel item #e95YV. This is a 1,500 lbs capacity jack, that will provide 12" of travel, and has a built-in wheel for easy moving…

view full answer...

Answer 9

Hey Fred. The TowSmart Plug-In Trailer Connector Adapter - 4-Way Flat to 7-Blade item #TS74QR will need to be wired into factory wiring along with plugging into a 4-way connector. The TowSmart ProClass Trailer Connector - 4-Way to 7-Way and 4-Way…

view full answer...

Answer 10

Hello David, I wasn’t able to find the dimensions for the mounting bracket for the Patriot Hitches Square Trailer Jack w/ Reinforced Mount - Drop Leg - Sidewind - 28" Lift - 7K #PH66NR anywhere, so I took a stroll out to the warehouse and…

view full answer...

Answer 11

With the ARK Xtreme Off-Road Swing-Up Jack #ORJW500D in its lowest position it is 6.49" from the center of the mounting point to the top of the jack. The other end of the jack when fully retracted is going to be 18.89" from the mounting…

view full answer...

What Frame Dimensions Trailer Valet jack part # TV83FR Fits

Product Page this Question was Asked From

Continue Researching