Trailer Valet JXS Drill Powered Swivel Trailer Jack TV76FR Measurements

Question

Question:

Looking at the Trailer Valet JXS Drill Powered Swivel Trailer Jack w/ Wheel - Sidewind - 14 Lift - 1.2K Part Number: TV76FR. I need 2 dimensions that I cant find. The height of the jack from center line up and the distance from the trailer AFrame to the jack how far it sticks out on the side of the trailer so I know what clearance is with other stuff like my weight distribution bars.

asked by: Robert P

0

Expert Reply:

Hi Robert,

I made a quick diagram of the Trailer Valet JXS Drill Powered Swivel Trailer Jack # TV76FR linked below with the measurements you asked for. It is pretty crude (I am definitely no artist), but I think it gets the point across. Basically you are looking at 16" from the center point of the frame mounting bracket to the top and 3" from the frame to the back of the jack.

Let me know if you have any other questions!

expert reply by: Lazer S

0

Jack
(click to enlarge)

Answer 1

The Trailer Valet #TV64FR JXS 5K trailer jack is a pipe mount swivel jack that can be removed from the trailer by pulling the pin shown in the provided photo. If you click the provided link, you can see a video showing a typical installation.

view full answer...

Answer 2

Hi David; for a replacement jack I recommend the Trailer Valet JXS Drill Powered Swivel Trailer Jack w/ Footplate #TV64FR. This jack has a 5,000 lb capacity so it will be a lot easier to operate compared tot the Fulton one you have now. You also have…

view full answer...

Answer 3

It sounds like you may need to add some more grease to the Trailer Valet JXS Trailer Jack #TV64FR. With the performance of the jack getting worse the portion of the screw inside the jack is likely drying out making operation with the Drill Attachment…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Trailer Valet JXS Drill Powered Swivel Trailer Jack TV76FR Measurements

Continue Researching