Best 4-flat Wiring Harness For The 2018 Land Rover Velar

Question

Question:

Hello - I was able to install the Draw-Tite hitch on the car - looks great. However, I am really struggling to figure out what flat four wiring harness is compatible with my 2018 Velar. Thanks

asked by: John T

0

Expert Reply:

Hello John, thanks for reaching out. We do have a wiring harness that can be used on your 2018 Land Rover Velar. There are no custom harness options available for this vehicle, but what you can use is the ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit # 119250KIT

This uses Zero Contact Interface (ZCI) clamps that go over the vehicle wires and detect electrical pulses. So this is the best way to add a 4-flat since you will not have the cut or splice any of the vehicles wires.

What are you planning on towing?

expert reply by: Jesse M

0

119250KIT
(click to enlarge)

Jesse M.

9/8/2025

Hey John, did the ZCI wiring harness work out for your Velar? I'm curious to know because it could help others who are in a similar situation.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Best 4-flat Wiring Harness For The 2018 Land Rover Velar

Continue Researching