Ramps for Motorcycle Trailer
Updated 09/12/2025 | Published 05/22/2025
Question:
I purchased new hubs, bearings, and tires for this old 3-rail motorcycle trailer from etrailer, but I have not had any luck locating a loading ramp to actually get the bikes onto the trailer. I contacted the dealer whose sticker is on the frame- they suggested it is likely an old Bandit or Load Rite trailer but they do not have any ramps available. Id ideally be looking for something that will hook on to the handle-/D-shaped end of the rail to stop the ramp from slipping.
asked by: Mike G
(click to enlarge)
(click to enlarge)
Expert Reply:
Hi Mike; how wide are the ends where the handle is attached? You may be able to use the Flint Hill Goods Easy Carry Trailer Ramps # FHG63ZR. Assuming they are 11" wide on each end the tabs for the ramps will sit right on there and you can get your bikes onto the trailer. If that works for your I recommend cutting off those handles since they would only be in the way. If you really want something that will hook on over those your best bet is to talk to a local fabricator to see if they can make a custom ramp for the trailer.
Product Page this Question was Asked From
Flint Hill Goods Easy Carry Trailer Ramps - Steel - 4' x 11" - 1,600 lbs - Black
- ATV Ramps
- Ramp Set
- Fixed
- 11 Inch Wide
- 1600 lbs
- Flat
- 48 Inch Long
- Steel
- Flint Hill Goods
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Replacement Ramp for etrailer Aluminum Motorcycle Carriers
- Article: RV AC Not Cooling? What's Normal, What to Check, and When to Replace
- Shop: Arched Loading Ramp - Center Fold - Aluminum - 88-9/16" Long x 13" Wide - 750 lbs - Qty 1
- Video: Replacement Ramp for etrailer Aluminum Motorcycle Carriers Spec Review
- Search Results: motorcycle ramp
- Search Results: hitch anti~rattle
- Search Results: atv ramps
- Shop: Flint Hill Goods Easy Carry Trailer Ramps - Steel - 4' x 11" - 1,600 lbs - Black
- Shop: Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches - 3-1/2" Span
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Q&A: Recommended Trailer Ramps for Loading a 4-Wheeler in a Low-Sitting Trailer
- Search Results: safety strap
- Video: All You Need to Know About the Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches
- Video: Review of Caliber Truck Ramps - Single Ramp - CA44KJ
- Video: CargoSmart S-Curve Loading Ramp with LED Lights Low-Down
- Video: Flint Hill Goods Loading Ramp Set Feature Review
- Video: An In-Depth Look at the Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches
- Q&A: Can Arched Loading Ramp # 288-07452 be Used for Loading into Truck Bed
- Video: Review of Erickson Ramp Safety Cinch Strap - EM95WV
- Shop: Trailer Wiring
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer wiring
- Search Results: trailer tires and wheels
on ATV Ramps
Robin H.
9/12/2025
Hey Mike, did you have a chance to measure the width of the ends where the handle is attached? I'm curious if the Flint Hill Goods Easy Carry Trailer Ramps worked out for your motorcycle trailer. Your experience could really help others facing the same challenge.