Which TST Tire Pressure Monitor System with 6 Standard Valve Stem Sensors

Question

Question:

Looking at TST-507 tpms for my 6 wheel motorhome that tows Jeep. What system is appropriate for this application? The remote sensor - is it mounted on the MH or on the towed jeep? I prefer standard sensors over flow through if possible.

asked by: Glenn M

0

Expert Reply:

Hey Glenn, the TST TPMS kit you are looking for is the part # TST-507-RV-6-C which is a 6 sensor kit that has standard sensor caps that do not flow through.

You'd want to put the signal booster on the motorhome towards the rear.

expert reply by: Jameson C

0

Glenn

5/8/2025

Thanks - but - the unit you suggested has flow through sensors. Also, what a bout my jeep? I need to monitor the 6 wheels on the coach and the 4 wheels on the jeep. I’d like to do that with cap sensors rather than flow through.

Jameson C.

5/8/2025

@Glenn Oh man I'm sorry about that. I was looking through the list of options and copy pasted the wrong part number. I meant to send you the part # TST-507-RV-6-C which does not have the flow through sensors. Then for four additional sensors you'd need the part #

Glenn

5/8/2025

@JamesonC - and the part number for the additional sensors is??? Seems like it got cut off. THANKS

Jameson C.

5/8/2025

@Glenn part # TST-507-RV-S4 It did get cut off for some reason. Sorry again...

Answer 1

They Thomas, I'd be glad to help you pick out which tire pressure monitor system would be better for you. So generally what we have found is that the TST system part #TST-507-RV-4-C is a bit more rugged and will withstand a little more abuse…

view full answer...

Answer 2

Each of the ball positions on the Gen-Y Torsion 2-Ball Mount #325-GH-1325 are separated by 3 inches. So at the very bottom is 9 inches, next up is 6 inches, 3 inches, and then zero drop. In the highest position is 3 inches of rise.

view full answer...

Answer 3

Hey Adam, we have the replacement SE2 cap sensor part #TST47FR that will work with what you have and is pretty small so it wouldn't stick out far enough to cause you any issues or problems with curbs. These are sold individually too so you…

view full answer...

Answer 4

The tire pressures called for either by the Chassis, RV or Tire manufacturer are the cold inflated tire pressures. There is no need to adjust the tire pressures while you drive unless you are travelling very long distances and in different climates.…

view full answer...

Answer 5

Yes, the Counteract Tire Balancing Beads #CA45FR will work perfectly with your TPMS, but you will need to remove the external sensor prior to injecting the beads. The only time that using these balancing beads with a TPMS gets tricky is when the TPMS…

view full answer...

Answer 6

I reached out to the manufacturer, TST, for you about the TST TPMS for RVs - 6 Tire Sensors #TST-507-RV-6-C and TST TPMS for RVs - 6 Flow Through Tire Sensors #TST-507-FT-6-C. I was told that for your set up, with rubber valve stems and steel valve…

view full answer...

Answer 7

The TST TPMS for RVs part #TST-507-FT-6-C is what I recommend using to monitor the tire pressures on both the motorhome and towed vehicle. This system uses the flow-through sensors which will be best because motorhomes usually have valve stem…

view full answer...

Answer 8

According to my contact at TST, going with the internal sensor would have the following benefits: • Battery Life. The internal sensors can be expected to last 5+ years, versus about 1 to 1-1/2 years for the external. • Protection: By virtue of the…

view full answer...

Answer 9

At this time there isn't a great all in one kit for TMPS and rear camera but I still do have some great options for you. For the camera system Furrion is the way to go. The base would be the Furrion Vision S Wireless RV Backup Camera System w/…

view full answer...

Answer 10

Since the GM TPMS uses a proprietary software so you aren't going to be able to use another sensor with the program even if they operate on the same frequency. So, with that being said, your best option is to use a standalone system like the TST…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Which TST Tire Pressure Monitor System with 6 Standard Valve Stem Sensors

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching