What is the Difference Between the Tekonsha BRAKE-EVN Trailer Brake Controller TK28BR and TK63VR?

Question

Question:

Im in the market for an electric brake controller for my 2008 Toyota Highlander. Im interested in a Tekonsha BRAKE-EVN controller for my 2-axel camper. What are the differences between Part Number: TK63VR and Part Number: TK28BR? Is the only difference that the second one comes with a 12-inch plug-in harness? Thanks in advance for your help.

asked by: Joe T

0

Expert Reply:

Hey Joe! The BRAKE-EVN Trailer Brake Controller item # TK28BR and item # TK63VR have exactly the same controller. The only difference in the two part numbers are that item # TK28BR comes with the wiring harness you'll need to connect to your Highlander's factory wiring.

If you have any additional questions feel free to throw them into the comment box below.

expert reply by: Jerred H

0

Jerred H.

9/26/2025

Hey Joe, did the Tekonsha BRAKE-EVN controller work out for your Highlander? I'm curious because it could help others looking to set up their brake controllers.

Answer 1

There is no need to unplug a brake controller when it's not in use and typically something like the Curt Reflex C51130 shuts off automatically after a certain time period-usually around 15 minutes. These won't drain your battery when sitting…

view full answer...

Answer 2

Brake controllers like the Tekonsha #TK63VR are all designed to use a sleep mode that allows them to keep their settings programmed so you don't need to reset the settings each time you turn on your vehicle. Disconnecting it will remove your…

view full answer...

Answer 3

Anything is possible, including getting you that manual. I've attached the owner's manual for the Tekonsha BRAKE-EVN #TK63VR that you can check out below. Just let us know if you have any other questions.

view full answer...

Answer 4

Since you mentioned that your brakes are brand new it's very likely you have a set of self-adjusting brake assemblies that just haven't adjusted fully to the point of activating strongly. This is a very common problem actually and has a very…

view full answer...

Answer 5

If your 2008 Toyota Highlander has a converter box under the dashboard already then you have the factory tow package. To give you an idea of what to look for I've attached a video of the trailer wiring being installed onto a Highlander without…

view full answer...

Answer 6

Since your 2008 Toyota Highlander Hybrid has the factory tow package all you need to install a 4-way is the part #56042 which plugs into a port at the rear of the vehicle very easily. I attached an install video for this kit on a similar 2008…

view full answer...

Answer 7

On the 2008 Toyota Highlander, the component that connects under the dash is the converter box. This is used to convert the 3 wire vehicle signals into 2 wire signals used by trailers by combining the directional and brake light signals into a single…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

What is the Difference Between the Tekonsha BRAKE-EVN Trailer Brake Controller TK28BR and TK63VR?

Continue Researching