Is There Version of 2k Rated Trailer Hub with EZ Lube Spindle Access Dust Cover

Question

Question:

Our trailer is a 1980ish Shorelander, single axle. We dont have the make and model. For this hub assembly, do you offer it with greaseable hub caps instead of just the dust caps?

asked by: Gary F

0

Expert Reply:

Hey Gary, we do have a version of the 2k rated trailer hub with a dust cap that has zerk fitting access with the part # AKIHUB-545-2-EZ-2K.

expert reply by: Jameson C

0

Jameson C.

9/26/2025

Hey Gary, did the hub with the zerk fitting work out for your Shorelander trailer? I'm curious to know if it was the right fit for your needs, as it could help others with similar trailers.

Answer 1

Due to the size of the brake drum that comes with the trailer axle part #e43SR the smallest wheel size that can fit with it is 13 inch.

view full answer...

Answer 2

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 3

While we do have a hub that fits the same spindle and is 12 inch wheel compatible the #8-258-5UC1-EZ will not fit a 12 inch wheel as it's mounting flange is too big. Instead you'd want the part #AKIHUB-545-2-1K which will work great for you.

view full answer...

Answer 4

Our 2,000 lb. trailer axles use both 1" and 1.06" diameter spindles. In order to determine you are receiving the correct hub assembly, you will want to use a digital caliper like part #PTW80157 to ensure you have an exact measurement. If…

view full answer...

Answer 5

view full answer...

Answer 6

To select a set of replacement idler hubs for your Fleetwood Destiny trailer you want to match up a few characteristics from your originals. These include the axle weight capacity, wheel bolt pattern and the bearing set used in the hubs. A…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

An EZ lube spindle will be better because it allows you to insert grease from inside the spindle where the bearings are and push out the old grease whereas with a Bearing Buddy you basically just get to push grease through the front of the hub. I…

view full answer...

Answer 9

In order to see if we have a compatible axle for you, it is important to measure the correct dimensions from hub face to hub face and spring center to spring center. I went ahead and attached a diagram that shows you how to conduct these measurements…

view full answer...

Answer 10

EZ Lube spindles are generally preferred over Bearing Buddy setups. The EZ lube allows you to insert grease down the middle of the spindle easily which is basically the best option aside from removing the hub and taking it all apart and cleaning and…

view full answer...

Answer 11

It is possible we have the right hub and drum (which I think is what you were referring to by brake drum kit) for your older boat trailer, but more information is needed to determine the right hub for your trailer, which I can help you figure out.…

view full answer...

Answer 12

Hi Adam, The smallest wheel sizing for a 3,500lb axle hub is 13" so you would have to switch up to a larger wheel and go with a manual-adjust 10" brake assembly #AKEBRK-35 or self-adjust #AKEBRK-35-SA. The correct hub/drum assembly will…

view full answer...

Is There Version of 2k Rated Trailer Hub with EZ Lube Spindle Access Dust Cover

Product Page this Question was Asked From

Continue Researching