Correct Harness to Use with TecNiq LED Trailer Tail Light # TN33XR

Question

Question:

Is this the right plug for the light ? Light TN33XR Plug A45PMB THANKS

asked by: George G

0

Expert Reply:

Hey George, the correct plug to use with the light # TN33XR is the part # A45PMB that you referenced.

expert reply by: Jameson C

0

Jameson C.

10/22/2025

Hey George, how did the plug A45PMB end up working with your TecNiq tail light? Knowing how the connection turned out could help others matching the same parts.

Answer 1

The fender we have that matches your needs the closest will be the Single Axle Jeep Style Trailer Fender #HP96VR. This has a polished diamond plate aluminum finish and measures 10" Wide, 33" long, and 17" tall, but is the boxier and…

view full answer...

Answer 2

For 3,500 pound axle U-bolt kits like the Redline #APUBR-1 that use 1/2 inch hex nuts you will want to torque them down somewhere between 45 and 70 foot pounds. I have attached a great article on trailer suspension that includes this info along with…

view full answer...

Answer 3

We have not yet replaced the Shock part #T1242600 on a Titan Model 10 Surge Brake Actuator so I do not have any specifics for you but I have attached a parts diagram which shows you how the unit is broken down. You can then use this to get a better…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Correct Harness to Use with TecNiq LED Trailer Tail Light # TN33XR

Product Page this Question was Asked From

Continue Researching