Adapter to Go from Pullrite Superglide to MORryde Cushioned Pin Box

Question

Question:

I am currently using the Pullrite superlite 2400, and my fifth wheel has a Morryde pin box. I feel more movement than I did when I had a fixed pin box. Would this adapter plate help with chucking?

asked by: John Z

0

Expert Reply:

Hey John, since you have a PullRite hitch what you need is the part # MR57ZR. This is correct adapter to go from your Superglide to the MORryde pin box. This will get rid of the movement.

expert reply by: Jameson C

0

John Z.

3/21/2025

I do not have a super glide hitch. As per my question I have a superlite hitch.

Jameson C.

3/24/2025

@JohnZ Sorry about that! I did see that but assumed it was a typo. If I could post an emoji it would be the facepalm guy haha. In that case yes you would need the part # MR37ZR.

John Z.

12/2/2025

@JamesonC I have installed this adapter, and it has stopped the excessive flex the stock Morryde plate had with my superlite hitch. Installing the rods through the plastic blocks were very tight. Now it doesn't seem to have any fore and aft movement. It's like a fixed pin box now. Is this normal, or should I still have some movement? Or should I use a traditional fifth wheel hitch and put the stock Morryde plate back on?

Jameson C.

12/2/2025

@JohnZ which adapter do you have? I don't see any in your order notes that I can pull up.

See All (7) Replies to John Z. ∨

Answer 1

For a very similar fireplace we have the Furrion part #FF34SW15ABL which is 33-7/8 inches wide, 17-3/4 inches tall and 6-1/4 inches deep. The wall cut out dimensions are 30-9/16" wide x 16-1/4" tall x 5" deep.

view full answer...

Answer 2

Hey Steve! The PullRite SuperGlide #PUL83RR will not contact the tailgate on your 2025 GMC Sierra 2500. They have tested this extensively and said making contact and causing damage is not a concern. This is a really great hitch and autoslide is the…

view full answer...

Answer 3

The problem is we don't have any gooseneck setups that have a 36k capacity at all, and the options that allow for both gooseneck and fifth wheel have considerably lower capacity than you'd need.

view full answer...

Answer 4

Hey Marvin! Which Trailair pin box do you have? Assuming it is the Trailair Air Ride like the #LC155943 you were looking at the correct capture plate is the PullRite SuperGlide Quick Connect Capture Plate for Trailair Air Ride Pin Boxes #PUL97ZR. If…

view full answer...

Answer 5

The Demco Hijacker Autoslide 5th Wheel Trailer Hitch w/ Slider - Single Jaw - Above Bed - 18,000 lbs, #DM8550034 and the Curt Q24 5th Wheel Trailer Hitch w/ R24 Slider - Dual Jaw - 24,000 lbs, #C16546 are both great hitches. The Demco Autoslide moves…

view full answer...

Answer 6

Yes, the MORryde Pin Box Adapter #MR57ZR will fit a MORryde Cushioned 5th Wheel Pin Box for 14K to 18K Trailers w/ Lippert 1621HD #MR84VR. This will allow for you to use your PullRite SuperGlide 5th Wheel Trailer Hitch to tow your 5th wheel trailer.

view full answer...

Answer 7

Hey Dave, yes, I can definitely help with that. For the Curt Rail Kit #C16429-204 you will torque all 1/2" hardware to 110 ft-lbs, and all 5/8" hardware to 210 ft-lbs. The U-bolts are 75 ft-lbs. I have provided a screenshot, as well as a…

view full answer...

Answer 8

Yes, the Curt Crosswing fifth wheel hitch part #C86JR is compatible with the cushioned MORryde pin boxes but you also have to use the #MR37ZR. The only MORryde pin box it's not compatible with is the pivoting Orbital pin box.

view full answer...

Answer 9

Hello Mike, thanks for reaching out. Yes, you can use the Andersen Ultimate Connection 5th Wheel Trailer Hitch System with a MORryde Cushioned 5th Wheel Pin Box such as part #MR24VR.

view full answer...

Answer 10

Hi Eric, Thanks for sending over that part number! The Lippert part number V000617833 does cross reference directly to our part number #LC48DX, and that part number is specifically associated with a Lippert Edge awning. Based on that information,…

view full answer...

Answer 11

I took a measurement of the B&W Tow & Stow 3-Ball Mount #BWTS20049C and found from the base to the bottom of the receiver it measured about 8-1/4 inches while the overall vertical measurement was about 11 inches. I have made a photo for you…

view full answer...

Answer 12

We haven't had the chance to install the WeatherTech Mud Flaps #WT110065-120065 onto a 2017 Ford F-350 as of yet but I did take a measurement you can use. I measured from the point where they install onto the truck to the bottom of the mud flap.…

view full answer...

Adapter to Go from Pullrite Superglide to MORryde Cushioned Pin Box

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching