Lippert V000617833 Right Drive Arm Replacement for 2000 Series Edge Awning

Question

Question:

Good Evening, I am looking for a part. it is the right drive arm of a lippert 2000 series. I believe the part number from lippert is Part V000617833 - RPLC-HDW-STDMTR-DRIVE-2000XBK-58-SLDBK-TOPWIRE-SWKITBK-OM

asked by: Eric S

0

Expert Reply:

Hi Eric,

Thanks for sending over that part number! The Lippert part number V000617833 does cross reference directly to our part number # LC48DX, and that part number is specifically associated with a Lippert Edge awning. Based on that information, LC48DX would be the correct replacement drive arm assembly if you have the Series 2000 Edge awning.

The only thing giving me pause is the additional string of characters before V000617833. Those extra characters typically contain configuration information about the awning, and without confirming exactly what they reference, I don't want to assume we're looking at a standard Edge setup.

If you can send me the awning model information, or the item number from the label that's usually located on the mounting arm near the RV wall underneath the fabric, I can verify everything and make sure LC48DX is the correct replacement before you order.

Where do you usually take your RV camping? Any windy destinations that may have contributed to the arm needing replacement?

expert reply by: Heather A

0

lippert
(click to enlarge)

Answer 1

Since your Solera arm is 58 inches long that would indicate it's a Solera Edge awning which means for a replacement drive arm you would want the part #LC22ED or for a replacement idler arm part #LC62ED.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hello Gary, thanks for providing all of the info and part numbers for your awning. That does come back as one of the Lippert 2000 series awnings. It sounds like you might be looking for the Replacement Pitch Arm Assembly #LC93BX which is for the 2000…

view full answer...

Answer 4

Hi Jesus, The number you provided comes back as a Solera Edge awning in black, but we'll need a bit more information to determine the correct arm because there's 3 different models in black. There should be another sticker on the arm with a…

view full answer...

Answer 5

For your 58 inch Lippert Edge RV awning the correct replacement idler arm is the part #LC62ED and the correct replacement drive arm (one with the motor) is the part #LC22ED.

view full answer...

Answer 6

Since you said you have the 58 inch arms that would indicate that you have the Lippert Edge awning which we have just the replacement arms for. For the idler arm you'd want the part #LC62ED and for the driver arm part #LC22ED.

view full answer...

Answer 7

For your 58" long arms, you're going to need the Replacement Idler Arm Assembly for Lippert Edge RV Awnings with LEDs #LC62ED for the Idler arm, and Replacement Drive Arm Assembly for Lippert Edge RV Awnings with LEDs #LC22ED for the drive…

view full answer...

Answer 8

In order to determine the correct replacement for your Lippert Edge awning you'll need to measure the length of your wall mount (see attached photo). Once you've got that number you can look for a replacement based off of that measurement.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Lippert V000617833 Right Drive Arm Replacement for 2000 Series Edge Awning

Continue Researching