What TorkLift Camper Tie Downs For 2024 Ford F350 Crew Cab Long Bed?

Question

Question:

Any chance that the TL54VV would work on a 2024 F350 Crew cab long bed?

asked by: Will

0

Expert Reply:

Hello Will, thanks for reaching out. The correct TorkLift tie down set for your 2024 F350 crew cab long bed is part # TL87DR.

The # TL54VV you mentioned comes with the correct rear tie downs F3008, but not the correct front tie downs for your F350.

The # TL87DR comes with the F3008 rear and F2032 front tie downs which are correct for the F350 crew cab long bed with the factory installed hitch.

I hope this helps. Leave a reply below with any questions or comments and I will get back to you.

expert reply by: Jesse M

0

TorkLift Camper Tie Down Example
(click to enlarge)

Jesse M.

10/27/2025

Hey Will, did the TorkLift tie downs from the TL87DR set fit your F350 crew cab long bed the way you needed? Knowing how they worked out could help others setting up the same truck.

Answer 1

Hi Josh, Yep, the TorkLift SuperTruss Hitch Extension for SuperHitch Trailer Hitch Receivers - 32" Long #TLE1532 can absolutely work to tow a boat trailer. This has a 6,500 lb towing and 650 lb tongue weight capacity with the SuperHitch Original…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

What TorkLift Camper Tie Downs For 2024 Ford F350 Crew Cab Long Bed?

Products Featured in This Question

Continue Researching