What Grease Cap With Rubber Plug and Stainless Steel Wear Sleeve do I Need for TDE 1750 Hub/Rotor?
Updated 11/03/2025 | Published 01/16/2025
Products Featured in This Question
Question:
I will be installing a new Tie Down Engineering 1750 hub/rotor PN: 46244 on my dual axle boat trailer with disc brakes on all 4 wheels. It came with rear bearing and seal installed and the front bearing loose. I need the dust cap with the rubber stopper on the end so i can access the grease fitting. I also want to replace the stainless steel wear sleeve on the axle. Do you have these items? I dont know what sizes or part numbers to buy. Can you help? Thanks
asked by: Gary A
Expert Reply:
Hello Gary,
I can most definitely help you with those part numbers. For the Tie Down Engineering 1750 hub/rotor PN: 46244 you will want the 2" Lubed Dust Cap & Rubber Plug Qty 1 # DC200L-DCRP. For the wear sleeve on the spindle you will want to use the Spindle Grease Seal Set # BB60002.
What lake do you usually go out on? What kind of boat do you have? The winter is usually my favorite time to go out and fish, but the sub zero temps in Missouri these last few weekends makes for a solid ice boat ramp.
Product Page this Question was Asked From
Kodiak 10" Hub-and-Rotor Assembly - 5 on 4-1/2 - Dacromet - 3,500 lbs
- Trailer Hubs and Drums
- Hub with Rotor
- Standard
- L68149 / L44649
- Marine Grade
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Kodiak
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: hitch pin
- Shop: CE Smith Trailer Wheel Lug Nut - Zinc-Plated Steel - 1/2" - Qty 1
- Search Results: safety cables
- Shop: etrailer Electric Trailer Brakes w/ Dust Shields - Self-Adjusting - 12-1/4" - Left/Right - 10K
- Q&A: Electric Trailer Brake Assembly for 10k & 12k Axle
- Q&A: Replacing Warner 12 Inch Electric Brakes & 6 Bolt Mounting Flange
- Search Results: rv vents and fans
- Q&A: Recommended Replacement for Imperial 55 Inch Side-Door Bar Lock
- Search Results: 8~285~10
- Search Results: rotor
- Search Results: 8~256
- Search Results: 7~224
- Shop: Replacement Trailer Hub Wheel Stud, Drive-In, 1/2" x 1-13/16" (Qty 4)
- Shop: Dutton-Lainson Hand Winch - TUFFPLATE Finish - 2 Speed - Direct Drive - 2,500 lbs
- Shop: Kodiak Hydraulic Brake Line Kit - Single Axle - 18'
- Shop: Replacement Drive-In Trailer Hub Wheel Stud - 5/8"-18 x 2-3/4" Long - Quantity 1
- Shop: Dexter Trailer Hub and Drum Assembly for 8,000-lb Axles - 12-1/4" - 8 on 6-1/2 - Oil Bath
- Q&A: Replacement Hub/Rotor and Bearings for Tie Down Engineering TDE46245
- Q&A: Replacing Older Tie Down Engineering 46210 and 46845 Trailer Hubs
- Q&A: Idler Hub To Replace TDE 46245 Hub and Rotor On Boat Trailer
- Q&A: Can Curved Equalizer EQ-E1 be Used with 7,000 Pound Axles
- Article: How To Measure And Replace Everything In Your Hub Assembly
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: Electric Trailer Brakes: How They Work & What to Buy
- Article: How to Bleed Your Trailer Surge Brakes
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: How to Tell the Weight Rating of a Trailer Axle
Kate F.
11/3/2025
Hey Gary, how did things go with the new dust caps and spindle grease seal set for your boat trailer hubs? Your update could make it easier for the next person working on a similar setup.