Can the Curt Heavy Duty Forged Ball Mount for 2-1/2" Hitch C93JR Be Used in the Rise Position?

Question

Question:

Can I flip this over and use it as a 6” rise?

asked by: Steve

0

Expert Reply:

Yes, you can Steve! The Curt Heavy Duty Forged Ball Mount item # C93JR comes with the hitch ball already preinstalled though. You'll just need to remove it.

The Curt Heavy Duty Forged Ball Mount item # C93JR is designed for a 2-1/2" hitch and comes with a 2-5/16" ball.

expert reply by: Jerred H

0

Jerred H.

11/3/2025

Hey Steve, how did things go when you flipped the Curt heavy-duty forged ball mount for the 6" rise? Your results could really help others looking to use the same setup.

Answer 1

Hey Dave, thanks for reaching out. We have just the thing! To add a 7-way to the bed of your 2026 Ford F-250, you will need the following: - Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector for Aluminum Beds - 10' Long #C57010

view full answer...

Answer 2

The Curt Ball Mount for 2-1/2" Hitches #C45460 does seem to have pretty round corners. Most likely they made it this way so that it can fit in the Ford 2-1/2 inch hitches which are known to have very round corners and hard to fit ball mounts…

view full answer...

Answer 3

Depending on the ball mount, you can use it in the rise or drop position. Some ball mounts, like #45291, can only be used in the drop position. The Reese Titan Ball Mount, #RP45323, that comes in the etrailer Ball Mount Kit, #EBMK25518, can be used…

view full answer...

Answer 4

We measured the distance from the center of the hitch pin hole to the center of the hitch ball and found that measurements was 10-1/2 inches for the Curt Ball Mount for 2-1/2" Hitches #C45460. This ball mount has a 20,000 lb capacity and gives…

view full answer...

Answer 5

To add a heavy duty trailer hitch to your 2023 Chevy Silverado 3500, I recommend the Curt Trailer Hitch item #C96CR. This hitch is custom fit and bolts to your Silverado with included hardware. This hitch only fits the standard Silverado 3500's…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Can the Curt Heavy Duty Forged Ball Mount for 2-1/2" Hitch C93JR Be Used in the Rise Position?

Product Page this Question was Asked From

Continue Researching